Victor Jr. 23š heads are designed for competition and ultra high-performance street small blocks and accept valve train hardware designed for standard 23š Chevrolet heads. They have a 550+ hp potential, out-of-the-box, for a cost effective, race-winning set-up. High-flow precision-cast 215cc intake runners offer excellent port alignment with Fel-Pro #1206 intake gaskets (recommended) without the need for port matching. These heads also feature .300” raise exhaust ports and 64cc or 70cc chambers with hardened, ductile iron valve seats and phosphor bronze guides. A 9/16” thick deck surface provides superior gasket retention. Valves are 1-piece, stainless steel high-quality construction.
(more…)

• 0 Comments

Before beginning this installation, take a few minutes to preread these instructions. Check that all necessary materials, units and accessory kits that are listed in the application guide are on hand. It is imperative for proper engine operation and vehicle life that adequate engine cooling is provided (i.e. fan shroud and/or large fan). Also check the vehicle weight capacity as listed on the vehicle certification label. Advice is hereby given by the vehicle manufacturer that for proper driving and handling, the reserve weight capacity not be exceeded, refer to the manufacturer recommended sizing guide
(more…)

• 0 Comments

The following instructions begin after the timing cover and old timing set have been removed.
Installing the timing set and degreeing the camshaft will be easier if you loosen the rocker arms so that the camshaft can turn freely. You should be able to turn the camshaft by hand. Make sure that the engine mounting surfaces and your new timing set have been thoroughly cleaned with a good solvent. If you are using a timing set with three keyways, select the appropriate keyway for your camshaft timing specifications. COMP Cams ® recommends the standard timing position for most applications. This position uses the round or “O” timing and keyway marks. Standard Timing Location: This is the same as original O.E.M. setting. Use keyway and crankshaft gear tooth marked “O”.
(more…)

• 0 Comments

Installation Instructions:
Pull and recline front seats all the way forward. Flip rear seat bottom up and fold seat back down.
Set the DU-HA in truck, centered on the floor, with DU-HA lettering facing forward (as shown). Make sure slot in the DU-HA is aligned with center child safety seat bracket.
With the DU-HA centered on floor use the DU-HA as a template to mark and drill two 5/16” holes in the floor flaps. Flip up the front flap to make sure the DU-HA is positioned against the rear of the cab before drilling. If you do happen to drill through the duct below the floor flaps they are only pressure release vents for cab pressure so a hole will not affect them. It’s best to secure driver’s side first before drilling passengers’ side.
(more…)

• 0 Comments

1. Remove stock timing cover. Rotate engine to top dead center of cylinder #1 so that the timing marks on the original crank and cam sprockets are directly lined up with each other, i.e. the mark on the crank sprocket will be at 12 o’clock (straight up) and the mark on the cam sprocket will be at 6 o’clock (straight down).
2. Remove sprockets and chain.
3. Install desired offset bushing from enclosed set. Set selection provides 0-Gray,
2-Gold, 4-Copper, 6-Silver, 8-Black, Camshaft Degree Options.
4. Install cam and crank gears.
(more…)

• 0 Comments

Installation of a Performance Automotive Group body lift kit will change the vehicle’s center of gravity and handling characteristics both on- and off-road. You must drive the vehicle safely! Extreme care must be taken to prevent vehicle rollover or loss of control, which could result in serious injury or death. Avoid sudden sharp turns or abrupt maneuvers and always make sure all vehicle occupants have their seat belts fastened.
(more…)

• 0 Comments

Installation Instructions. Read Me! Rv. 01/04
1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove throttle body air intake system.
3. Remove (3) nuts & studs from the throttle body & manifold. (Ref. “C”)
4. Remove support bracket from engine block to throttle body. (Ref. “D”)
* Please Note: When removing support bracket bolt at engine block, loosen bolt enough to remove bracket. DO NOT REMOVE BOLT.
(more…)

• 0 Comments

This bulletin is being revised to add the 2005 model year and update the part number information for Permatex Quick Grid. Please discard Corporate Bulletin Number 03-08-44-005B (Section 08 — Body and Accessories).
Condition
Some customers may comment that the radio has poor reception or radio static/increased interference when the rear window defogger is turned on. Also, some rear window defogger grids may be inoperative.
(more…)

• 0 Comments

Lay out the exhaust and compare part numbers with the drawing.
To remove stock exhaust cut your stock tailpipe off, remove hangers from rubber grommets, use wd-40 to help with removal. now un-bolt your factory exhaust at the flanges located just after your y-pipe.
Bolt passenger side headpipe # a onto factory dome using hardware kit # l. do not tighten. insert hanger into rubber grommet, next slip driver side headpipe # b onto factory pipe use clamp # h to secure. do not tighten next install muffler #c. slide it onto headpipe 1-1/2” to 2”. attach to headpipes with clamp # h. inlet shoud go towards the motor. inlet of muffler is looking into the louvers. do not tighten. outlets will be on the bottom.
(more…)

• 0 Comments

1. Raise and support vehicle at a safe, comfortable working height. Let the front suspension hang freely
2. Remove oem coil spring and shock absorber. Refer to a factory service manual for proper disassembly procedure.
3. Due to the Shockwave bellow being larger than the coil spring you will have to open the coil spring pocket as shown by the white circle in the picture. You will also need to remove the lip of the coil spring retainer and cut between the large holes as shown in the picture. This is best done with a plasma cutter, cutoff wheel, or saw.
(more…)

• 0 Comments