LIGHT DISARM RESISTORS
The resistors are connected into the wiring at each wheel to bypass the original dampening solenoid so that the Road Sensing Suspension will function without giving the driver a suspension error message on the instrument cluster.

INSTALL RESISTORS
Cut the wires leading to the dampening solenoid on the strut/shock. Connect the wires to the ends of the resistor. (This is an in-line resistor so it does not matter which wire goes in or out.) Tape up both ends with suitable electrical tape to prevent both shorts and corrosion. Tie back out of way with a plastic strap.
(more…)

• 0 Comments

READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS BRACKETRON PHONE MOUNT. All instructions are written from the drivers seat position looking forward at the vehicle dash. We advise caution whenever you are removing or handling plastic parts of a vehicles dash. WARNING: Unnecessary force or pressure can cause pieces to crack or break
(more…)

• 0 Comments

Because this is a “Race Only” product, it will not meet emissions standards. As it is a “Race Only” product, it will also cause the “Check Engine” light to be illuminated after three complete driving cycles. This is not a problem for maximum performance. The “Check Engine” light will not cause the engine computer to go into a “Safe Mode”. It is only a system function indicator. Special Note on the handling of your Jackson Racing Stainless Steel header: Congratulations on your purchase of the Jackson Racing Stainless Steel header. This is the finest header on the market today. It is constructed from 100% stainless steel. Including the flanges. It will not rust! But special care must be taken during the installation and handling of the Stainless Steel if you want the tubing to always look good.
(more…)

• 0 Comments

The AS-100 Anti-skid Drive System is intended for use by the professional aircraft maintenance technician. Use by consumers or other unqualified personnel is not recommended.
Notes:
1. The 4 wheel anti-skid system installed on the Falcon 10 & 50 and others requires the use of 4 Drive Motors with 4 PN AS-300-101 axel adapters.
2. The Messier-Bugatti anti-skid system installed on the Falcon 900 requires the use of the 6 Drive Motors with 4 PN AS-300-203 Axel Adapters, 2 P/N AS-300-204 Axel Adapters.
(more…)

• 0 Comments

This B&M Precision Sport Shifter has been designed to work on most 2002+ Acura RSX/Honda Integra (including 6- spd Type-S) and 2001+ Honda Civic models equipped with a manual transmission. It has been engineered to greatly reduce shift throw and improve shifter feel. Check the parts and tools lists at the beginning of these instructions for the supplied parts and the tools required to install your B&M Precision Sport Shifter. Installation of the B&M Precision Sport Shifter can be accomplished by anyone with minimal mechanical experience.
(more…)

• 0 Comments

This document contains additional instructions specific to the BMW R1200RT. Please see the wiring instructions included with the heated seat(s) wiring kit for wiring detail.
Installation:
Wire the heated seat(s) and heat controller(s) per the wiring diagram included in the heated seat(s) wiring kit. This wiring diagram is also available on our website. Use the photos below to locate the recommended switched relay wire connection point, and proceed to wire the heated seat(s) and controller(s) per the wiring diagram.
(more…)

• 0 Comments

THE FIRST THING TO DO IS TAKE INVENTORY of the parts received. Get familiar with the parts! The hardware list on the next page will list all fasteners by size and where they go. You’ll need to use assembly lube or grease for installing the urethane bushings. We use Valvoline #612 multi-purpose red grease. Loctite #609 is provided with this kit. Use it on all threaded fasteners.
(more…)

• 0 Comments

Using Audi-specific radio removal keys, remove the radio from the dash by pulling toward you after the four locks have been disengaged. The radio fits very tightly into the opening even when the locks are released. Disconnect all plugs from the back of the factory radio, remove and set aside. MAKE SURE THAT YOUR RADIO IS NOT CODED OR THAT YOU HAVE THE CODE BEFORE
(more…)

• 0 Comments

Read and understand these instructions BEFORE attempting to install this product.
1) Getting started
a) Make sure vehicle is parked on a level surface.
b) Set parking brake.
c) Disconnect negative battery terminal.
d) If engine has run within the past two hours let it cool down.
(more…)

• 0 Comments

The NEW BMW 7 Series door lock (Shown Below) – You will not be able to decode the door lock with the tool because the angle of the lock will prevent you from obtaining the correct readings. However, you will be able to decode the boot lock on this model of car successfully.
Note: in some models you have to apply a little bit of force in order to open the car but not to much because excessive force can bend the half key bits.
(more…)

• 0 Comments