Read all instructions before starting any work. This kit is designed to connect to DynoMax Blackjack painted / Cyclone ceramic coated, or competitive brand, full length Headers.
1. Bolt adapter plates 703828 to hangers 703825 and 159496 using the ⁵⁄₁₆”-18thd x ģ⁄₄” bolts and nuts provided. See the system diagram for parts identification. The plates will allow 2đ⁄₂” size saddle clamps to be connected to the hangers.
2. On the cross member frame of the vehicle, slightly forward of the rear axle, there is a set of two mounting holes on each side, LH and RH, which will be used to mount hanger 703825 on the LH side and hanger 159496 on the RH side. use the ⁵⁄₁₆” -18thd x 1″ bolts nuts provided.
(more…)

• 0 Comments

OPi-A8 is a direct iPodо interface developed for Audi vehicles utilizing the MOST fiber optic bus. OPi-A8 is designed to interface with current versions of the iPodо and iPodо Nano. Once installed, OPi-A8 allows the ability to control iPodо functions from the vehicle’s head unit, and also allows partial control of iPodо functions (volume adjustment and track control) from the vehicle’s steering wheel controls. To minimize driver distraction, the iPodо interface buttons will not respond while the iPodо is docked and the OPi-A8 is active. While the iPodо is docked with the OPi-A8 interface, the iPodо will automatically begin charging. In order to activate the OPi-A8 your radio must be in CD changer mode. Vehicles equipped with factory installed CD changers will lose the function of the CD changer once the OPi-A8 is installed. Vehicles that do not have a factory installed CD changer will not lose any radio functions.
(more…)

• 0 Comments

These installation instructions are mainly intended for use in the MINI dealership network and by authorised BMW Service Centres. The target group of these installation instructions are technical personnel trained on MINI vehicles with corresponding technical know-how.
All work is to be carried out with the aid of currently valid MINI repair instructions, schematic circuit diagrams, maintenance manuals and working instructions in rational order with the specified tools (special tools) while paying particular attention to valid safety regulations.
(more…)

• 0 Comments

The AEM Cold Air Intake System is the result of extensive development on a wide variety of cars. It is the most advanced Cold Air Intake System on the market. Each system is specifically engineered for its application. All AEM Cold Air Intake Systems deliver maximum performance gains through lightweight, all-aluminum, mandrel-bent tubing that is tuned in both length and diameter. The aluminum will not crack in extended use like plastic. The tube length and diameter are matched for each specific engine to give power over a broad RPM range. Unlike plastic systems that use a continually diverging cross-section, we take advantage of the acoustical energy in the inlet duct to promote cylinder filling during the intake valve-opening event. Every intake is coated with a high-gloss, heat-reducing Zirconia based powder coating.
(more…)

• 0 Comments

1 ) Set aside a couple of cups of the portland cement to be used for the final finishing stages of the repair.
2 ) Cut or chisel the length of the crack creating a notch 1” wide and ―” to 1” deep. Examine the edges of the notch – they should not be smooth. Roughen up the edges if necessary so that the repair will bond firmly to the existing floor.
3 ) Wet the notched area thoroughly.
4 ) Mix the portland cement with the terrazzo chips to create a consistency which is not runny nor is it thick like dough. A consistency you can hold in your hand.
(more…)

• 0 Comments

For BUICK & CADILLAC
Originate New Master Key
1. Insert properly cut key into ignition and turn it to the ON (RUN) position. The security light on the dash will illuminate for 10 minutes.
2. Within one minute of the light going out, turn the ignition cylinder to OFF and then back to the ON (RUN) position. The security light will illuminate and stay on for another 10 minutes.
3. Within 1 minute of the light going out, turn the ignition cylinder to OFF and then back to the ON (RUN) position. The security light on the dash will illuminate and stay on for 10 more minutes.
(more…)

• 0 Comments

RaDIo FuncTIonS:
• How to get to the XM band
– Select XM1 or XM2 with the BAND button
• Tuning in XM channels
– Scroll through XM channels with the TUNE knob
– When you change channels, the radio will display the Channel Number/Name, then revert to the default display
– Press SEEK once to select the next channel, or press and hold for 2 seconds to scan through all channels; SCAN will be displayed. Press and hold for 4 seconds to scan through all preset channels; SCAN and the preset number will be displayed
(more…)

• 0 Comments

TO START:
1. Turn off the ignition and disconnect the negative battery cable.
2. Disconnect the mass air sensor electrical connection and unhook the mass air sensor wiring from the engine cover.
3. Remove the two screws shown that secure the fresh air tube to the fresh air duct.
4. Pull up firmly on the air filter housing/engine cover assembly to release it from the mounting grommets.
NOTE: The air filter housing/engine cover assembly is still attached to the intake inlet tube.
5. Using pliers, release the spring clamp that secures the intake to the intake inlet. Then unhook the intake tube from the inlet.
(more…)

• 0 Comments

General notes before you use your new parts …
1. The new Bugatti door handles you have purchased are an exclusive product of Model Motorcars, Ltd., based entirely on proprietary research of prototypes and exclusive miniature manufacturing technology, and are only available through us. Please beware of imitations and copies.
2. Our Bugatti door handles are designed to be used as a substitute for the Pocher supplied parts, although some work to modify the doors to adapt the handles is required. Therefore, they are only suggested for experienced Pocher builders adept at modify the kits extensively.
(more…)

• 0 Comments

SCHROTH BMW specific asm-Rallye 4 Series harnessbelts are only intended for installation at the left and right outboard front seating positions of designated BMW and MINI model passenger cars which have been specifically evaluated by SCHROTH engineers for anchor point locations and suitability of available front seats. Before attempting installation, please first answer the following questions and carefully follow the instructions which accompany them.
(more…)

• 0 Comments