This Borla Performance Exhaust System (part number 11774 & 11775) has been designed for 2010 Chevrolet Camaro equipped with a 6.2L V-8 engine with an automatic or manual transmission. Borla Performance Exhaust System (part number 11776) has been designed for 2010 Chevrolet Camaro equipped with a 3.6L V-6 engine with an automatic or manual transmission.
(more…)

• 0 Comments

First, PLAN YOUR PROJECT!!! Know how you want it to look when it’s finished. This will be repeated many times because it can’t be said enough. Do you intend for it to be hi-tech or old style? Billet wheels or painted steelies? Pro street? Pro touring? Ground scrapping low? Who’s going to drive the car and where? Is it going to be a low mileage show car or a (more…)

• 0 Comments

The Edelbrock E-Force Competition Air Intake System is intended only for use on 2010-2011 Chevrolet Camaro SS’ that have been equipped with the Edelbrock E-Force Competition Supercharger System. This intake is not compatible with naturally aspirated cars, nor with those using a different supercharger. While this system can also be used with the #1597/1598 street legal packages, installation may violate emission regulations in some areas.
(more…)

• 0 Comments

Cylinder Heads
Mark IV cylinder heads, made by Chevrolet, will not interchange to a stock, production Gen.V Chevy block. There will be a water leak into the lifter valley because of a mismatch of water jacket core holes. Likewise, stock production Gen.V cylinder heads, made by Chevrolet, will not interchange onto Mark IV block cases for the same reason. There are exceptions. You can put Mark IV cylinder heads on a Gen.V “Bowtie” block because the Gen.V “Bowtie” cases have smaller (more…)

• 0 Comments

The Optra is a front-wheel-drive compact car from GM DAT (General Motors Daewoo Auto and Technology). It is available in sedan, hatchback and, new for the fall, station wagon models. Similar in size to the Civic, Focus, Elantra and Corolla, its main rivals, it is powered by a 2.0-litre Four. We test drove the hatchback version.
(more…)

• 0 Comments

Poor Engine Performance – Misfire, Rough Idle, Stalls, Engine Cranks but Does Not Run, Service Engine Soon/Check Engine Light Illuminated, DTC P0300 Set (Inspect Distributor Ignition (DI) System Components and Replace As Necessary)
This bulletin is being revised to delete a model and add information to subject and inspection of distributor vent screens. Please discard Corporate Bulletin Number 03-06- 04-041 (Section 06 – Engine/Propulsion System).
(more…)

• 0 Comments

This kit is designed to work with 15” or larger wheels.
Instructions:
1. Disconnect the rear hard lines on the rear axle from the wheel cylinders.
2. Disconnect the rear brake hose from the hard lines on the axle.
(more…)

• 0 Comments

REMOVING THE ORIGINAL DISTRIBUTOR 1. If the vehicle has a manual transmission, place the gearshift in neutral and chock the wheels. This prevents the crankshaft from being accidentally turned and the distributor mounting reference lost, if someone pushes or leans against the vehicle. Automatic transmissions should be placed in “Park”.
2. Disconnect the ground cable from the battery.
3. Remove or relocate the engine parts, such as air cleaners, that block access to the distributor.
(more…)

• 0 Comments

A step by step instructional manual on the proper installation of the Geared Drives PSRU for Chevrolet V8 engines, including lubrication and maintenance recommendations.
The Geared Drives BW350 Propeller Speed Reduction Unit (PSRU) is shipped with the clutch and flywheel unit already (more…)

• 0 Comments

This document covers the installation of RECON Truck Accessories 3-Piece running lights on a 2003 Chevrolet/GMC Silverado/Sierra 2500 HD.
The installation takes approximately 2 to 3 hours and can be broken down into 5 main steps:
(more…)

• 0 Comments