This kit was not designed to fit vehicles with a body lift.
TO START: 1. Turn off the ignition and disconnect the negative battery cable. NOTE: Disconnecting the negative battery cable erases pre-programmed electronic memories. Write down all memory settings before disconnecting the negative battery cable. Some radios will require an anti-theft code to be entered after the battery is reconnected. The anti-theft code is typically supplied with your owner’s manual. In the event your vehicles’ anti-theft code cannot be recovered, contact an authorized dealership to obtain your vehicles anti-theft code.
(more…)

• 0 Comments

If your original radio had a braided strap bolted to the rear of the radio.
TIP: Crimp a ring terminal to the new radios ground wire and insert a bolt through both connectors to connect the ring terminal of the braided ground wire to the ring terminal attached to the new radios ground wire.
If your original radio had a plastic connector containing a single wire plugged into the rear of the radio.
TIP: Crimp a male tab spade to the new radios ground wire. Slide it into the female tab spade connector that had originally snapped into the rear of the factory radio.
(more…)

• 0 Comments

Dual Fueler CP3 Pump Kit Installation Guide 03-07 5.9 Dodge Cummins
Engine noisy – Too Much Fuel Pressure or fuel delivery code
1) Cause: Check fuse is good and in controller’s fuse holder securely, and all power connections are secure, including connectors for both pumps are fully plugged in.
2) Lift pump pressure supplying both CP3 pumps pressure too high. Supply pressure from lift pump should not exceed 12-15 psi.
(more…)

• 0 Comments

PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
2. Starting at the Passenger/Right side-front of the vehicle, remove the front factory body bolt & washer.(not re-used) (Fig 1), From the list above select the Passenger/Right side front mounting bracket and the spacer Block secure to vehicle with (1) 12mm x 150mm Hex Bolt, (1) 12mm Flat Washer, (1) 12mm Lock Washers (Fig 1A). Snug but do not tighten hardware at this time.
3. Next, select the T Bolt from the list of parts above, and place the T Bolt into the opening on the Passenger/Right side bottom front frame rail (Fig 2 shows T Bolt placed into frame rail.
(more…)

• 0 Comments

Front Door Installation for Magnum, Charger, 300C
1. Using a pick tool pry open the screw covers behind the interior door release lever and below the
arm rest and remove the screws. Fig. 1
2. Remove the four screws securing the door panel along the bottom. Fig. 1
3. Using the end of a Phillips screwdriver gently depress the center pin of the three plastic retainers
securing the door panel. The center pin of the plastic retainer should depress approximately 1/8”
and allow the retainer to be removed from the door panel. The two uppermost retainers do not
need to be removed in order to remove the door panel. Fig. 2
(more…)

• 0 Comments

Vehicle preparation:
1. Remove the negative battery cable before installing the cruise control components for safety precautions.
2. Jeep wrangler applications: remove airbag by using (3) trim tool to release metal clips as shown in figure 2. Caution: ensure that battery has been 90 seconds disconnected for more than prior to removal of airbag; failure to heed this warning may result in airbag discharge and may cause serious injury or death.
(more…)

• 0 Comments

This manual is divided into different areas to assist you with your installation and operation of your braking unit. We strongly suggest that you write down the kit and serial numbers of your unit in the spaces provided and retain this manual for any future reference
Kit Contents
2033135 – 1988-1998 Dodge Cummins 12V Exhaust Brake Kit
1 1230030 Vacuum Control Kit (w/ Micro Switch)
1 1230335 Vacuum Spool Valve Kit
1 2133030 Exhaust Brake
(more…)

• 0 Comments

Read and understand these instructions BEFORE attempting to install this product
1) Getting Started
a) Make sure vehicle is parked on a level surface.
b) Set parking brake.
c) If engine has run with in the past two hours let it cool down.
d) Disconnect negative battery terminal. ~:
e) Raise front of truck and support with properly rated jack stands.
f) Remove passenger side, front tire.
(more…)

• 0 Comments

INSTALLATION NOTES
1. Unless specified, mount all Sub-Frame components to vehicle before tightening any bolts.
2. Vehicle should be parked on a level surface with the
front suspension normally loaded.
MOUNTING INSTRUCTIONS
1. Locate existing slotted holes in vehicle frame rails directly above front axle.
2. Install Mounting Bracket (#3)RH, using three (3) 5/8″ x 2″ Capscrews (#10) Washers, and Nylock Nuts provided.
(more…)

• 0 Comments

The Mag-Hytec pan is designed to fit the factory Dodge #727 transmission body as supplied as original equipment. However, in some applications, or because of the use of certain factory options and/or after market equipment, there may be clearance problems between your Mag-Hytec pan and other vehicle components. It is the responsibility of the vehicle owner and installer to ensure that there is no contact between the pan and other moving or fixed vehicle components. Contact with any vehicle component or the modifying of the Mag-Hytec pan voids the warranty. Mag-Hytec assumes no liability, expressed or implied, for damage or injury to persons or property.
(more…)

• 0 Comments