Entries Tagged as 'GMC'
This document covers the installation of RECON Truck Accessories 3-Piece running lights on a 2003 Chevrolet/GMC Silverado/Sierra 2500 HD.
The installation takes approximately 2 to 3 hours and can be broken down into 5 main steps:
(more…)
This manual describes features that may or may not be on your specific vehicle either because they are options that you did not purchase or due to changes subsequent to the printing of this owner manual. Please refer to the purchase documentation relating to your specific vehicle to confirm each of the features found on your vehicle. For vehicles first sold in Canada, substitute the name “General Motors of Canada Limited” for Pontiac Motor Division wherever it appears in this manual.
(more…)
Installation Instructions: Tilt the seat forward. Remove the plastic wing nut from the current plastic jack cover, behind the seat. Thread the metal extension coupler (provided) onto the shaft in the current plastic jack cover.
(more…)
1. Prepare the work area. Since this installation requires handling turbocharger and exhaust components, the vehicle should be cold. A top-side creeper will be a very valuable to ease this job. Alternatively, rolled shop towels can provide some cushion when laying over the engine while working on the turbocharger and exhaust pipes. Have a shop light handy.
2. Raise the hood fully. Locate and disconnect the negative lead from both batteries.
(more…)
1. Locate Rear Bumper Attachment
Locate the rear bumper attachment point on the driver’s side of the vehicle.
2. Remove Rear Bumper Fasteners
Remove the bumper fasteners. Set them aside to be reused.
3. Assemble Linkage to Mounting Bracket
Assemble the Mounting Bracket to the Linkage.
2500 & 3500 HD Vehicles: Use the M10-1.5 x 35 Socket Cap Screws. Do not use the Spacer.
Other Vehicles: Use M10-1.5 x 80 Socket
Cap Partial Thread Screws Spacer and the Spacer.
4. Install Linkage Assembly
Slide the holes in the Mounting Bracket over the studs on the vehicle. Reinstall the fasteners removed in Step 2.
5. Install Step
Use the M6-1.0 x 20 Socket Head Cap Screws to mount the Step to the Linkage Assembly.
6. Adjust Step
Adjust the Step from side to side. Make sure to leave clearance for foot access to lower step. Tighten the allen head bolts.
Operation
The TrekStep™ is foot operated and deploys and retracts with a nudge of your foot. To deploy, press down using your left foot, on the forward outside corner of the step pad. To retract, gently kick the underside of the step pad. Max Load Capacity: 300 lbs. Always use appropriate hand holds when stepping up to or down from your truck’s cargo bed.
Maintenance Tips
The step pad surface and linkage arms can be washed with mild soap and water using a soft brush or sponge to dislodge any mud, dirt or accumulated road grime. Rinse with fresh water. To prevent slipping, avoid applying waxes, lubricants
Attention!
TrekStep™ SHOULD ALWAYS BE STOWED IN THE RETRACTED POSITION WHEN DRIVING.
Vehicles application: Chevrolet P-30 & GMC P-3500
The axle has a banjo-type housing with a removeable carrier. The drive pinion is straddle mounted on removeable carrier. There is no adjustment for drive pinion depth or bearing preload. The preload on the differential side bearings is set by adjusting nuts on which the bearing cups rest. The differential has a two-piece case and four differential pinion gears.
(more…)
DESCRIPTION & OPERATION 1985-86 BRAKES Disc & Drum – “C”, “G”, “K” & “P” Series
BRAKE BOOSTER
Delco-Moraine Single Diaphragm
A combined vacuum-hydraulic unit which uses a combination of intake manifold vacuum and atmospheric
pressure to provide power assist. Reserve vacuum supply and vacuum check valve allow several brake
applications, with vacuum assist, after engine has stopped.
Unit is composed of 2 main sections. The vacuum power cylinder and the dual master cylinder. Vacuum power
cylinder contains power piston assembly, which houses control valve, reaction mechanism, and power piston
return spring.
(more…)
Proper installation of this kit requires knowledge of the factory recommended procedures for removal and installation of original equipment components. We recommend that the factory shop manual and any special tools needed to service your vehicle be on hand during the installation. Installation of this kit without proper knowledge of the factory recommended procedures may affect the performance of these components and the safety of the vehicle. We strongly recommend that a certified mechanic familiar with the installation of similar components install this kit
(more…)
The polished black cover on each mirror can be removed and painted to match the vehicle’s body color, or replaced with chrome (p/n 9040) or ‘USA Flag’ theme covers (p/n 9060). Find below the removal/installation instructions for the cover.
Existing cover removal.
Make sure you have the required tools:
• flashlight
• slotted screwdriver (with at least a 5” shaft).
Approximate installation time: 5 –10 minutes.
(more…)
Installation Instructions:
Pull and recline front seats all the way forward. Flip rear seat bottom up and fold seat back down.
Set the DU-HA in truck, centered on the floor, with DU-HA lettering facing forward (as shown). Make sure slot in the DU-HA is aligned with center child safety seat bracket.
With the DU-HA centered on floor use the DU-HA as a template to mark and drill two 5/16” holes in the floor flaps. Flip up the front flap to make sure the DU-HA is positioned against the rear of the cab before drilling. If you do happen to drill through the duct below the floor flaps they are only pressure release vents for cab pressure so a hole will not affect them. It’s best to secure driver’s side first before drilling passengers’ side.
(more…)
Categories
Archives
Cars PDF Document is proudly powered by WordPress - BloggingPro theme by: Design Disease