2003-2004 (KJ) Jeep® Liberty NOTE: This notification applies only to the above vehicles equipped with Remote Keyless Entry (Sales Code GXM) built from April 1, 2003 through December 12, 2003 (MDH 0401XX through 121200).
The rear flip-up window switch on about 120,000 of the above vehicles may be improperly sealed and could allow water to enter into the switch. This can cause the flip-up window to open unintentionally if it is left unlocked. The rear flip-up window switch must be replaced on all affected vehicles.
(more…)

• 0 Comments

Entertainment Systems - FLO TV
FLO TV`99 service provides a superior mobile TV experience that is available to over 200 million people in 105 major U.S. markets. Many key transportation corridors will be covered by the FLO TV network and coverage will extend to 95 percent of where these Americans live, work, drive. That means that you can receive 24/7 programming to keep your entire crew entertained, regardless of the trip duration. Even if you`ve got to keep your eyes on the road, you can enjoy listening to 60 Minutes from CBS Mobile or the
(more…)

• 0 Comments

Kit parts are prefaced by the word kit and appear in bold print. 1. Carefully read all warnings and instructions completely before beginning.
2. Verify all parts have been received in this kit by checking the parts list at the end of this document.
3. Only install this kit on the vehicle for which it is specified. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-3175.
4. Park vehicle on a clean, dry, flat, level surface and block tires so vehicle cannot roll in either direction. Adhere to recommendations when replacement fasteners, retainers and keepers are called out in the factory service manual. When re-assembling the vehicle it is recommended (more…)

• 0 Comments

Due to differences in manufacturing, dimensions and inflated measurements, tire and wheel combinations should be test fit prior to installation. Tire and wheel choice is crucial in assuring proper fit, performance, and the safety of your Pro Comp equipped vehicle. For this application, a wheel not to exceed 10” in width with a minimum backspacing of 3.25” must be used. Additionally, a quality tire of radial design, not exceeding 33” tall X 12.5” wide is recommended. Please note that the use of a 33” X 12.5” tire may require fender modification. Violation of these recommendations will not be endorsed as acceptable by Pro Comp Suspension and will void any and all warranties either written or implied.
(more…)

• 0 Comments

The mounting procedure outlined below covers the 1997-2002 Jeep Wrangler. Note that a
Front Gross Axle Rating (FGAWR) of 2500 lbs. is required. A suspension upgrade and additional
ballast may be necessary. You will need to refer to the illustrations and familiarize yourself with each
of the undercarriage components and their relative position to each other. Then proceed as follows:
Begin by removing the four screws that hold the plastic “Jeep” valance in place above the
bumper. Keep these screws as they will need to be reinstalled.
(more…)

• 0 Comments

Installation of a Performance Accessories suspension lift kit will change the center of gravity and the handling characteristics of the vehicle. Because of the higher center of gravity and larger tires, the vehicle will handle and react differently both on and off road. You must drive it safely! Extreme care must be taken to prevent vehicle rollover or loss of control, which could result in serious injury or death. Avoid sudden sharp turns or abrupt maneuvers and always make sure all vehicle occupants have their seat belts fastened.
(more…)

• 0 Comments

WIRING OVERVIEW
Switch Settings (read below for explanation)
Selecting The Vehicle Type
Switches 1,2, and 3 are used to select vehicle type. Use the chart on the back of these instructions to determine which of the above switch settings you will need.
(more…)

• 0 Comments

The evaporative emission system is designed to prevent the escape of fuel vapors from the fuel
system. Leaks in the system, even small ones, can allow fuel vapors to escape into the
atmosphere. Government regulations require onboard Testing to make sure that the evaporative
(EVAP) system is functioning properly. The leak detection system tests for EVAP system leaks
and blockage. It also performs self-diagnostics. During self-diagnostics, the Powertrain Control
Module (PCM) first checks the Leak Detection Pump (LDP) for electrical and mechanical faults.
If the first checks pass, the PCM then uses the LDP to seal the vent valve and pump air into the
system to pressurize it. If a leak is present, the PCM will continue pumping the LDP to replace
the air that leaks out. The PCM determines the size of the leak based on how fast/long it must
pump the LDP as it tries to maintain pressure in the system.
(more…)

• 0 Comments

Open the liftgate and remove the upper liftgate trim panel.
Remove the right (passenger’s side) D-pillar trim panel.
Install audio/visual display to the right D-pillar trim panel as shown.
Remove the lower liftgate trim panel.
Remove the right C-pillar trim panel.
Remove the right inner quarter trim panel.
Remove the rear fascia and place it on a protected surface.
(more…)

• 0 Comments

1. Disconnect the negative battery cable. Loosen the hose clamp on air cleaner box lid. Twist and remove breather hose from air cleaner box lid. 2. Unhook the two air cleaner lid latches on front of box. 3. Remove the air cleaner box lid by sliding it forward, and then up, and out of the factory intake tube. 4. Remove factory air filter from air cleaner box. 5. Remove, and set aside the oil filler cap. Use caution not to drop anything into engine while cap is off. 6. Carefully lift up on the engine cover (it is held in place by grommets, no bolts) to access the hose clamp (more…)

• 0 Comments