FRONT INSTALLATION Read complete instructions before beginning installation, the following special tools are recommended: Coil spring compressor, floor jack, ball joint separator, jack stands, and metric hand tools. Jack the vehicle in the center of the front cross member. Support the vehicle by placing jack stands on the frame cross member so that the front tire/wheels are off the ground. Remove the front tires/wheels. Disconnect the sway bar end links and remove the upper ball joint cotter pin and nut. Separate the upper ball joint from the spindle. (Using ball joint separator or a suitable tool) Remove upper strut nuts on the strut tower (3) on each side of vehicle that holds strut (more…)
2009-2010 Altima and Maxima Front Strut Mounting Insulator RecaLL Campaign
18 Dec
Posted by admin as Nissan
Some specific model year 2009 – 2010 Altima and Maxima vehicles may have been built with front strut mounting insulators that were not manufactured to specification. The strut mounting insulators on these specific vehicles may crack. To remedy this potential condition Nissan is conducting this voluntary safety recall campaign to replace the strut mounting insulators with new ones at no charge for parts or labor.
(more…)
FRONT OF XTERRA
1. Park vehicle on level concrete surface.
2. Center and lock the steering wheel.
3. Block the rear wheels of the vehicle to prevent vehicle from moving in either direction.
4. Jack up the vehicle from the lift point in Figure A.
(more…)
Please remove the Std intercooler ,top Std intercooler pipe , front bar ,front reinforcement prior install the top Hybrid intercooler pipe. (make sure all super clamps are loose for further adjustments.) Hybrid Nissan R33 GTS intercooler kit Installation instruction Note Picture may be different than the actual product! It is a reference guide only! Page 2 Parts list Piping, silicon hose and super clamp kit 3 custom pips set Description Qty 2.5” super clamps 6 3”super clamps 2 2.5”-3” silicon reducer 2 2.5” silicon hose 2 Spacers 2 Screws 6 Nuts 2 Long lower bracket 2 Short top bracket
(more…)
Pre-fit before painting. Install new, unpainted parts according to these instructions. Then remove parts, paint them and re-install. Painted or Altered Parts are Non-Refundable. The exhaust system must be installed before the side skirts. Do not tighten exhaust clamps or bracket until installation is complete. The entire Sniper side skirt kit must be installed before exhaust tip installation. The surface temperature where the 2-sided tape is applied must be 75o or above. This temperature must be maintained for 24 hours without moving vehicle or the 2-sided tape will fail.
(more…)
Banks Monster® Exhaust System Dual-Tip 2007-2008 Dodge 6.7L Cummins ISB Pickup Trucks Including Mega Cab Owners Manual.
1. For ease of installation of your Banks system, familiarize yourself with the procedure by reading the entire manual before starting work.
2. The general assembly diagram (Figure 1) provides only general guidance. Refer to each step and section diagram in this manual for proper instruction.
(more…)
The DMF is bolted to a plate on the crank from the engine side. Access to the engine side of the plate can be found on the lower right side of the firewall. The flywheel must be rotated to remove all 8 bolts. Then remove plate from crank Orientation of release fork for Dodge Ram applications Please note that the clutch fork on this vehicle can be installed in the reverse position. When installed incorrectly, the result will be a “growing noise coming from the belt housing end/or a no release condition. Please refer to Figure Number 4 for the correct fork orientation during the assembly process.
(more…)
Installation Stainless Steel Oval on Dodge RAM HD Crew Cab:
1. Read instructions completely and check to make sure that all required parts (listed on service parts list) are on hand before starting the installation.
2. Oval step assemblies and brackets (item #1 & 2) are pre-assembled.
2.1. The front and rear mounting brackets on these assemblies are rotated for shipping purposes. These brackets must be rotated to the vertical position and the ‘/2″ bolts. Torque to 65 lb ft.
(more…)
1. Unplug all lights and harnesses connected to factory bumper and remove from truck frame.
2. Remove factory tow frame to install new Top Gun rear bumper. In order to remove tow frame, the bed of the truck has to be loosened on lifted 6 inches off the truck frame. Remove 4 bolts towards the rear of the bed, end loosen but do not remove the 2 bolts towards the front of the bed. Lift bed and remove towing frame.
(more…)
Thank you for purchasing the Self Leveling Kit for your Kelderman Air Ride System. The kit consists of an air compressor, air tank and height control valve and linkage The kit also includes the needed mounting brackets and hardware that will give the air ride automatic ride adjustment.
Installing the Self Leveling Kit
Step 1. Height Control Valve: This mounts to the top air ride frame (unless ‘94-’02 Dodge). To locate, hold the height control valve on top of the air ride top frame plate and set it so the front hole of the height control arm is equal to the end of the swing arm.
(more…)
Categories
Archives
Cars PDF Document is proudly powered by WordPress - BloggingPro theme by: Design Disease