Special Tool(s): Socket, Exhaust Gas Oxygen Sensor 303-476 (T94P-9472-A)
Material Penetrating and Lock Lubricant E8AZ-19A501-B High Temperature Nickel Anti-Seize Lubricant F6AZ-9L494-AA
Removal and Installation
(more…)

• 0 Comments

When working on, under, or around any vehicle exercise caution. Please allow the vehicle’s exhaust system to cool before removal, as exhaust system temperatures may cause severe burns. If working without a lift, always consult vehicle manual for correct lifting specifications. Always wear safety glasses and ensure a safe work area. Serious injury or death could occur if safety measures are not followed.
(more…)

• 0 Comments

The FP-611 (1998-Newer Ford Taurus base) is a no-holes passenger side base. Installing a no-holes base does not require drilling any holes into the vehicle. Installing the FP-611 Base in the vehicle:
1. Place both front seats of the vehicle in their most rearward position.
(more…)

• 0 Comments

The Power Module kit contains: – One (1) Power Module – One (1) Bracket – One (1) Cotton Swab
Tools needed: 1/4” wrench, 7mm and 13mm wrench, a phillips head and flathead screwdriver, and a small amount of lacquer thinner.
1. HYPERTECH POWER TUNING WAS DEVELOPED FOR 93 OCTANE PREMIUM GASOLINE. MAKE SURE YOU HAVE 93 OCTANE PREMIUM GASOLINE, OR THE HIGHEST OCTANE RATING AVAILABLE IN YOUR AREA, IN YOUR VEHICLE BEFORE INSTALLING THE POWER MODULE.
(more…)

• 0 Comments

Borla Performance Cat-Back™ Exhaust System (Part number 140337) has been designed for the Ford Taurus SHO equipped with a 3.7L twin-turbo V6 engine, all-wheel drive and automatic transmission.
Original Exhaust System Removal
Note: With a used vehicle, we suggest a penetrating spray lubricant to be applied liberally to all exhaust fasteners and allowing a significant period of time for the chemical to lubricate the threads before attempting to disassemble.
(more…)

• 0 Comments

(Applications – Ford Mustang, Crown Victoria, Ranger, F-150, and Explorer)
NOTE: Be sure to keep right and left bearing cups, shims, and bearing journal caps separated!
1. Install ring gear on Torsen differential. Torque bolts as specified in the Ford Service Manual.
2. Install two new journal bearings on Torsen differential.
(more…)

• 0 Comments

Removal: 1. Raise vehicle on a hoist, allowing the front suspension lower arms (3078) to hang free.
2. Remove wheel and tire assembly.
3. Remove disc brake caliper (2B120), then wire it out of the way to obtain working room.
4. Disconnect tie rod end (3A130) assembly from the front wheel spindle (3105) using Tie Rod End Remover TOOL-3290-D or equivalent.
(more…)

• 0 Comments

Proper installation of this supercharger kit requires general automotive mechanic knowledge and experience. Please browse through each step of this instruction manual prior to beginning the installation to determine if you should refer the job to a professional installer/technician. Please contact your dealer or Vortech Engineering for possible installers in your area. This (more…)

• 0 Comments

For those of you that have not come across or had the privilege of working on the Ford 4.0L SOHC cam engine you are about to get a baptism in its proliferation in the timing components used. Now before you go off and wonder why I am even trying to tell you about these, know this there are none available in the aftermarket (or at least not that I was able to find). You can buy tensioners, guides and chains but gears are not available from the aftermarket and as you see the proliferation you will understand why. So you will either have to purchase them new from Ford or you are going to reclaim those that are not worn or damaged.
(more…)

• 0 Comments

Removal and Installation
1. Disconnect the battery ground cable. For additional information, refer to Section 414-01.
2. Remove the accelerator cable snow shield.
3. Detach the spark plug wire retainer.
(more…)

• 0 Comments