Connect the ground wire from the CB radio chassis to the body For details consult a NISSAN dealer WARNING A cellular telephone should not be used while driving so full attention may be given to vehicle operation Some jurisdictions prohibit the use of cellular telephones while driving If you must make a call while your vehicle is in motion the hands free cellular phone operational mode if so equipped is highly recommended.
(more…)
Adjusting Height
1. Loosen plastic set screws on each leg (by turning them counterclockwise).
2. Select set of legs appropriate for your car (see back for chart).
3. Slide each leg up into the hollow vertical tubes on either side of the barrier grill.
4. Stand the barrier grill inside your car where you want it to be and lift it to the roof. The legs will slide down from the sleeve of the tubes.
5. Tighten each plastic set screw, making sure the barrier grill is pressing snugly against roof and floor. Make sure set screws are very tight before proceeding to next step.
(more…)
Tools Needed:
A drill
1″ hole saw
T27 Torx bit and driver with a 4″ extension
Extendable magnet
Pliers
or A drill with a smaller bit such as a 1/4″ A dremel or similar to cut a hole in plastic T27 Torx bit and driver with 4” extension Extendable magnet Pliers
(more…)
Volkswagen and Audi transfer the delivery instruction as well in the message type VDA 4905/1, in the ODETTE message type DELINS according to VDA 4905/2 as in EDIFACT DELFOR. The description of the VW/Audi specific use of the delivery instruction in the format VDA 4905/2 is available in the Internet for download, too. The VDA 4905/1 is transmitted for delivery instructions of the factories of the marque Volkswagen by the IVZ Wolfsburg (station ID R11) and for delivery instructions of the marque Audi by the IVZ in Ingolstadt (station ID R21). The delivery instructions of VW de Mexico and of the marque SEAT are routed outgoing from the IVZ Puebla (R66) or IVZ Barcelona (station ID R41) trough the IVZ in Wolfsburg to the partners within the area of the VDA.
(more…)
Borla Performance Cat-Back ™ Exhaust System Installation
1. Place a clamp over the expanded end of the front muffler assembly and set it into position as shown in figure 4 making sure to install the hangers into the rubber isolators. Do Not tighten the clamp.
2. Place a clamp over the expanded end of the rear muffler assembly and set it into position as shown in figure 5. Do Not tighten the clamps.
3. Check your exhaust system for proper clearance under the vehicle and also for tip alignment.
(more…)
Begin by carefully inserting all four (4) of the Audi radio removal tools into the slots on the face of the radio until you hear and feel a slight click. This locks the tool into place. Carefully pull the radio out of its cavity letting the radio rest on the center console. Hint: Place a clean towel under the radio to when resting on the console. This will prevent scratching the center console
(more…)
When any of the memory switches are pushed while the automatic drive positioner is operating When the adjusting switch for the driver s seat is turned on while the automatic drive positioner is operating When the memory switch 1 or 2 is not pushed and held for at least 1 second When the seat has been already moved to the memorized position When no seat position is stored in the memory switch When the automatic transmission selector lever is moved from P Park to any other position When the driver s door remains open more than 45 seconds and the ignition switch is not in the ON position The automatic drive positioner system can be adjusted and canceled For vehicles with navigation system see Vehicle electronic systems in the Display screen heater air conditioner and audio systems section of this manual For vehicles without navigation system see your NISSAN dealer Pre driving checks and adjustments
(more…)
This mount will provide a great reduction in transmission movement making shifting much more secure. With less transmission movement you’ll have less drivetrain slop as well, resulting in more power transmitted to the wheels. Upgraded engine mounts are recommended to be used in conjunction. Below are our installation guidelines for this item. Please review them carefully before attempting to install this product.
(more…)
Make sure you maintain the vehicle in a clean pristine condition, and trim components are undamaged and placed back into position. Prior to reinstallation, make sure you vacuum the inside of the cover where dirt is apparent. Make sure that all dirt is removed from the inside of the cover. Always protect the rear bumpers, painted and interior surfaces, on all vehicles during the installation. Have a clean terry cloth and cleaning alcohol with you to clean off any fingerprints on the interior of the vehicles.
(more…)
Audi Homelink The Integrated Gate and Garage Door Opener Operating Instructions
11 May
Posted by admin as Audi
The HomeLink system provides a convenient way to replace up to three remote controls with a single built-in component. This innovative feature learns the radio frequency codes of most current remote controls used to activate garage doors, property gates, security systems, and home or office lighting.
- When programming the HomeLink system to a gate or garage door opener, make sure that people and objects are out of the way to prevent potential harm or damage, in particular injuries due to trapped limbs.
- Retain the original remote control for future programming procedures (i.e. new vehicle purchase). It is also suggested that upon sale of the vehicle, the programmed HomeLink buttons should be erased for security purposes (please refer to Erasing Programmed HomeLink Buttons ).
(more…)
Categories
Archives
Cars PDF Document is proudly powered by WordPress - BloggingPro theme by: Design Disease