STEP 1. Begin by removing the small black trim ring that surrounds the radio. Insert the hook tool behind the upper right corner of the trim ring and pull toward you to loosen the ring. Once the ring is loose, work the remaining three (3) corners of the trim ring loose. Set the trim ring aside. Turn the ignition to the “ON” position and shift the transmission into low gear. Just above the ashtray door, grasp the top section of the bezel that surrounds the transmission shifter and pull toward you to release two (2) clips. Insert the hook tool behind the right rear corner of the bezel just behind the shifter. Pull upward to release one (1) clip. Perform the same action in the left rear corner releasing one (1) more clip. Grasp the rear of the bezel and continue working loose two (2) clips on the left and right sides of the shifter. Work the bezel up and over the shifter knob and disconnect all wiring. Set the bezel aside.
(more…)

• 0 Comments

DISASSEMBLY AND ASSEMBLY OF DIFF DROP KIT
1. Remove the 2 diff bolts on driver side differential that attach the diff housing to the frame mount. Install diff spacers (P/N C3DB) using new M12 X 1.75 X 50 bolts. This is to space the diff down ―” to improve the angle on the CV boots. See Fig. A
2. Repeat this process on the passenger side of the vehicle. Remove the 2 OEM diff nuts on passenger side differential that attach the housing to the frame. Install diff spacers (P/N C3DA) utilizing the supplied M12 x 1.75 nylon locking nuts. See Fig. B
(more…)

• 0 Comments

Before you begin
-Read instructions completely before starting each step.
-Pay attention to how parts are removed from the vehicle and make sure to keep track of all parts, in many cases they may be used in the installation.
Step 1. Radiator shroud removal
-Remove the plastic radiator shroud by removing the two plastic rivets with a flat blade screw driver or pry tool. To do this you must first unlock the rivet by prying up on the head of the rivet, located at the center (the head will raise about a half an inch).
-Once the rivet has been unlocked it can then be removed.
-There are two christmas tree style fasteners at each edge of the plastic shroud. These are removed by inserting your flat blade screw driver/pry tool near the fastener and gently prying upward.
(more…)

• 0 Comments

Remove the front bumper cover
A. Begin by removing the dust covers that are located underneath the vehicle. Use the 10mm socket to remove the OEM bolts and then the 7mm Nut driver to removed all the OEM screws along the sub-front portion of the bumper.
B. Locate and remove all other fasteners that attach the OEM bumper cover to the vehicle. Once you’ve removed the fasteners, slowly remove the bumper cover. Note that some vehicles may have the foam bumper protector inside, where some may have the plastic protector. The Pro-gard Push Bumper was designed for the plastic protector.
(more…)

• 0 Comments

Read all instructions and fully understand them before installing you TS Performance MP-8 module. Disconnect the battery terminals and remove keys from ignition before installation. Place Di-Electric Grease onto every electrical connection.
1. Remove the dipstick and 4 bolts holding the plastic cover plate on top of the engine.
2. Using an 11mm wrench remove the 2 clamps holding the EGR tube that crosses in front of the valve cover. You do not have to remove the tube only tilt the tube up towards the front of the truck.
3. Using a 10mm socket and wrench, remove the bolt that holds the dipstick tube to the bracket and the 6 bolts that hold the air horn to the manifold. Making sure not to damage the gasket, slide the air horn forward so that you can access the front of the fuel rail.
(more…)

• 0 Comments

Remove the heat exchanger from its carton and inspect for any obvious physical damage. All kit components are thoroughly inspected and carefully packaged prior to shipment from the factory. If any shipping damage is evident, contact your supplier and request that they process a claim with the shipper involved. Be sure to review the parts list on page 3 to verify that you have all necessary system components to proceed. If any components in the parts list are missing, contact Turbonetics’ customer service staff.
(more…)

• 0 Comments

REMOVAL OF EXISTING MIRROR:
1. Have both windows in the down position. Remove the trim panel on both doors, start by removing two philips screws. One is located in the hand hold and the other is in the corner in front of the window. (note – there are two trim panel clips below the window).
2. Remove the foam insulation covering the stock mirror mounting nuts.
3. Support the stock mirror while removing the 3 mirror mount nuts and then remove the stock mirrors.
(more…)

• 0 Comments

Step of the Installation Instructions:
1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Loosen the hose clamp and remove the air tube from the throttle body air box.
3. Disconnect the air temperature sensor connector attached to the air box.
4. Loosen the two bolts that secure the air box using a 10mm socket.
5. Remove the oil filler cap (for clearance if needed) and carefully pull and remove the air box. * Be careful not to drop anything in the oil filler pipe.
(more…)

• 0 Comments

This bracket provides the SOLUTION for installing a K20A (ITR/CTR/Euro R) cable actuated throttle body into a K-Powered EG, EK, DC2, or EF while:
-Enabling usage of a short OEM throttle cable (Acura 17910-ST7-L01) for swap cleanliness
-Eliminating throttle cable/bracket interferences (with fuel lines, hoods, hoses, etc.)
-Comprised of high quality billet 6061-T6 machined aluminum.
(more…)

• 0 Comments

This kit provides the SOLUTION for eliminating cruise control on throttle bodies found in the 02-06 RSX-S and 02-05 Civic Si while:
-Enabling usage of a short OEM throttle cable (Acura 17910-ST7-L01) for swap cleanliness
-Eliminating throttle cable/bracket interferences (with fuel lines, hoods, hoses, etc.)
-Essentially converting a K20A2/A3/Z1 throttle body into a K20A (Type R) throttle body
-Comprised of high quality billet 6061-T6 machined aluminum.
(more…)

• 0 Comments