The information below documents the procedure I used to install the Hella Micro DE fog lamps on Saab 92-X.
Disclaimer: This information is provided as a reference and the author assumes no responsibility for any damage that may result from this modification to your car.
1. Prep: I started by purchasing the stock Subaru Fog Lamp Relay and Fog Lamp Switch. Since the car is pre-wired for the factory fog lamps, this allows you to use the existing wiring for the installation of the Hella fog lamps.
The part numbers for the parts are: The Fog Lamp Relay is B48 in the diagram below and is the 3rd relay from the bottom. The location will be the only one empty. The Fog Lamp switch is connected to B160, which will be right behind the switch location. By removing the change holder, I was able to install the relay and switch, and plug the connector into the back of the switch without removing the lower dash panel, but it requires some patience.
(more…)

• 0 Comments

Installation instructions for the Eclipse, Stratus Coupe, and Sebring Coupe. (See reverse side for Mitsubishi Outlander, Lancer/Sportback, and Mitsubishi Montero instructions)
Locate and remove two (2) screws from the bottom of the trim bezel. With your hands or Dash Trim Tool (#SIT-104), release the bezel from all clips. There are two (2) clips on the bottom and two (2) on the top of this bezel. Remove bezel and set aside carefully.
(more…)

• 0 Comments

Installation Pro.Fit Kit on Ford Transit Connect. Place the DTRT and the Hook Tool in the space between the dash molding and the air vent bezel above and to the right of the radio. Use the hook tool first to gently pry up the air vent bezel sufficient enough to insert the DTRT. Use the DTRT in a gentle twisting motion around the bezel to release the eleven (11) retainer clips securing the air vent bezel to the dash molding. Place bezel off to the side. Insert four (4) Mercedes/Audi radio removal tools in the slots located in the four corners of the radio as indicated by the arrows in Picture 1. Follow radio removal instructions included with the radio removal tools part number (DM-20-22).
(more…)

• 0 Comments

Conflicts: JBL Audio, Factory Navigation, Accessory XM Satellite Radio, and Accessory Sirius Satellite Radio. Confirm available switch knock out prior to installation. Kit Contents: For kits manufactured on or after 18C9, installation kits will include (15) total lock ties and (2) adhesive foam pads. The manufacturing date code is on the part label of the packaging box and is printed as “DDMY”.” Please note that this manufacturing date is per Toyota standards and is in the format of DAY DAY-MONTH-YE AR. Example: “31L8” date on label means “31st, December, 2008”.
(more…)

• 0 Comments

This manual contains the pre-installation, assembly and installation for dual player headrest video on Toyota Prius 2010.
Pre-installation Precaution
1. Use Seat and Floor Protectors to avoid damage to surfaces.
2. If the vehicle is equipped with an Anti-theft radio, the radio code must be written down prior to disconnecting the battery cable. The code must be re-entered when the negative battery cable is reinstalled. Disconnecting the battery
Figure may cause certain vehicle settings to be lost. Manufacture’s recommendations for the battery B3 removal should be followed. Disconnecting the battery is recommended.
(more…)

• 0 Comments

Gauge bezel can be painted using a plastic safe paint.
1. Remove two screws in top of factory bezel. Use small screwdriver in the slotted area of the light switch knob to release tension on spring clip while pulling forward to remove knob.
2. Pull forward on bezel from the inside bottom, detaching clips from the dash.
3. Install aluminum brackets as shown in Figs. 1 and 2.
4. Place new gauge bezel in dash as a test fit. Adjust brackets so that screw holes align. Brackets can be rotated or bent to align holes.
(more…)

• 1 Comment

READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS BRACKETRON PHONE MOUNT. All instructions are written from the drivers seat position looking forward at the vehicle dash. We advise caution whenever your removing or handling plastic parts of a vehicles dash. WARNING: Unnecessary force or pressure can cause pieces to crack or break.
TOOLS NEEDED: Dash Trim Tool, (Part #SIT-104), 10mm socket and driver, #2 Phillips screwdriver.
PARTS INCLUDED: One phone mount , Three (3) #8×3/4” self tapping screws
LOCATION OF MOUNT: To the right of the radio
(more…)

• 0 Comments

Make sure you maintain the vehicle in a clean pristine condition, and trim components are undamaged and placed back into position. Always protect the painted and interior surfaces, on all vehicles during the installation. Have a clean terry cloth and cleaning alcohol with you to clean off any fingerprints on the interior of the vehicles. Note: The 2008 TT is currently the only vehicle that can be ordered with CD Changer prep or CD Changer. The 2008 R8 must have a CD Changer to accommodate this installation.
(more…)

• 0 Comments

Begin by carefully inserting all four (4) of the Audi radio removal tools into the slots on the face of the radio until you hear and feel a slight click. This locks the tool into place. Carefully pull the radio out of its cavity letting the radio rest on the center console. Hint: Place a clean towel under the radio to when resting on the console. This will prevent scratching the center console
(more…)

• 0 Comments

MAIN PANEL MOUNTING
Remove the OEM bezel and gauge cluster from the dash. Remove the entire factory gauge cluster from the bezel. From the back of the bezel, first insert the 5” round spacer so it sits flush against the inside of the bezel. Next, insert the smoked acrylic lens and secure with a small amount of glue, RTV or similar. Insert the speedometer pushbutton into the lens from the rear (the kit includes 2 different size buttons, select the one that fits such that the panel lays flat and the pushbutton has room to move), then install the panel so its sits against the four original retaining screw locations (at the 3, 6, 9 and 12 o’clock positions). The pushbutton will rest against a switch on the panel when properly installed and the LEDs will rest against the lens. Insert the 3 6/32 x ˝” screws through the panel and into the bezel at the original locations (using the approx. 3, 9 and 12 o’clock locations).
(more…)

• 0 Comments