This document describes the steps for upgrading a Need for Speed™ Underground Deluxe Motion Cabinet to Need for Speed™ Carbon. The Upgrade Kit includes a new computer, Software, Game Dongle, Artwork, and an external mounting bracket for the Nytric USB I/O PCB. Need for Speed™ Carbon software requires a new computer. You will need to remove the Digital- Analog Converter (DAC) card and Nytric USBI/O PCB from your existing computer.
(more…)

• 0 Comments

Instructions: There are four M10 countersunk bolts supplied with this kit.
2 x M10 x 40 (Standard Thread)
2 x M10 x 1.25 x 40 (Fine Thread)
These bolts are used to mount the upper brackets to the chassis. When the bump stop is removed the threaded hole must be examined to determine if it is a standard or fine thread.
(more…)

• 0 Comments

EGO TS is the intelligent entry-level solution for telephone use in your car: simple to operate, elegant and compact – with Bluetooth and audio enjoyment too. The installation of your EGO TS in your car requires specialist knowledge and skills. We recommend that the installation be carried out in a qualified professional workshop. Before installation in your car, please make sure that your mobile phone is fully compatible with EGO TS. If you are uncertain, please consult your dealer or a professional workshop. Our service team will also be happy to help you with any information you may require. You can find further information on compatibility between EGO TS and various mobile phones on our website.
(more…)

• 0 Comments

Preparation
1. Ensure all lamps and accessories are OFF.
2. Ensure the ignition switch is in the OFF position.
3. Loosen the negative battery cable bolt.
Remove negative battery cable from terminal and position away from battery.
4. Wait one (1) minute prior to working on the vehicle to assure SIR roof rail airbag system has been disabled for your safety.
(more…)

• 0 Comments

Preparation
1. Ensure all lamps and accessories are OFF.
2. Ensure the ignition switch is in the OFF position.
3. Loosen the negative battery cable bolt.
Remove negative battery cable from terminal and position away from battery.
4. Wait one (1) minute prior to working on the vehicle to assure SIR roof rail airbag system has been disabled for your safety. Install Camera into Endgate
(more…)

• 0 Comments

Installation Procedure:
1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove air cleaner
3. Using 1/2” socket, remove (3) 5/16’ bolts.
* Please Note: Some units have bolts that are drilled and tapped for air cleaner mounting studs.
4. It is not necessary to remove the fuel lines.
5. Remove fuel line bracket from transmission. (Located on drivers side of bell housing)
(more…)

• 0 Comments

Installation: 2005 Dodge Charger or Magnum
1. Remove the 2 plastic covers that protect the front area under the hood (Fig. 1). They snap into or out of the vehicle.
2. Remove the 2 bolts that hold the hood latch assembly on and set it aside (do not disconnect the cables). Unplug the horn wire and place the wire out of the way (Figs. 1 & 2).
3. Mount speaker to bracket (Fig. 3).
4. Remove all the plastic rivets from the top of the front of the body of the vehicle, then pull the body toward the front of the vehicle (the body is flexible). Slide the 2 U-Nuts onto the support braces (Fig. 4) and place the bracket (with siren attached) on top of the U-Nuts. The front “ears” of the bracket rest on the two U-Nuts which clip onto the support braces (Fig. 4). The rear of the bracket will mount behind the hood latch assembly using the hood latch’s mounting hardware (Fig. 2).
(more…)

• 0 Comments

Installation Instructions Procedures:
1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove air intake assembly.
3. Remove throttle body intake box and save bolts.
4. Remove (3) bolts from throttle body.
5. Remove bolts from throttle linkage bracket and save.
6. Install power plate using (3) 6mm x 60 bolts and (3) 6mm flat washers. (Ref. “A”)
(more…)

• 0 Comments

Installation Procedure for this body spacer:
1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove throttle body air intake assembly.
3. Remove (2) nuts from the throttle body and (2) studs from manifold. (Ref. “C”)
4. Remove gasket and clean surfaces.
(more…)

• 0 Comments

Included with your Poweraid Spacer is a sticker with a California Air Resources Board (C.A.R.B.) Executive Order (EO) number. This sticker must be placed in plain view inside of the engine compartment. Failure to do so may prevent you from passing a smog inspection.
Installation Procedure:
1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove air cleaner assembly.
3. Using 1/2” socket, remove (4) 5/16” bolts attaching throttle body to manifold.
4. Lift throttle body.
(more…)

• 0 Comments