Borla Performance Cat-Back™ Exhaust System (Part number 140337) has been designed for the Ford Taurus SHO equipped with a 3.7L twin-turbo V6 engine, all-wheel drive and automatic transmission.
Original Exhaust System Removal
Note: With a used vehicle, we suggest a penetrating spray lubricant to be applied liberally to all exhaust fasteners and allowing a significant period of time for the chemical to lubricate the threads before attempting to disassemble.
(more…)

• 0 Comments

DISASSEMBLY
1. Raise vehicle and support with proper jackstands for the weight, leaving the suspension hanging.
2. Use caution around hot exhaust systems to avoid burns.
3. Use penetrating oil on all nuts and bolts.
(more…)

• 0 Comments

This Borla Performance Rear Section Exhaust System (Part number 11762) has been designed for 2008 Nissan Altima equipped with a 3.5L V-6 engine and automatic or manual transmissions.
Original Exhaust System Removal
(more…)

• 0 Comments

The AWE Tuning RSK04 Fueling Kit picks up where the Audi RS4 leaves off! AWE Tuning worked very closely with GIAC to establish the proper mechanical parameters which would overcome limitations in the RS4 that GIAC documented during chip development. The RS4 Mass Air Flow (MAF) sensor and fuel injectors are inappropriate for use on an S4, and we also had our sights set even higher than chipped RS4 territory with the RSK04 kit.
(more…)

• 0 Comments

Caution!!! Never work on a hot exhaust system. Serious injury in the form of burns can result If the vehicle has been in use and the exhaust system is hot, allow vehicle to cool for at least 1 hour. Always wear eye protection when working under any vehicle. Note: It is our recommendation that you use a hoist or hydraulic lift to facilitate the installation of your new Borla Performance Cat-Back ™ Exhaust System. Taking all under car safety precautions, lift the vehicle using a hoist or hydraulic lift. Once this has been done, you may begin the removal of your old exhaust system from your vehicle. Note: Before removing the original exhaust system from your vehicle, please compare the parts you have received with the bill of materials provided on the previous page to assure that you have all the parts necessary for the installation of your new Borla Performance Cat-Back ™ Exhaust System.
(more…)

• 0 Comments

Borla Performance Cat-Back ™ Exhaust System Installation
1. Place a clamp over the expanded end of the front muffler assembly and set it into position as shown in figure 4 making sure to install the hangers into the rubber isolators. Do Not tighten the clamp.
2. Place a clamp over the expanded end of the rear muffler assembly and set it into position as shown in figure 5. Do Not tighten the clamps.
3. Check your exhaust system for proper clearance under the vehicle and also for tip alignment.
(more…)

• 0 Comments

Original Exhaust System Removal
Note: With a used vehicle, we suggest a penetrating spray lubricant to be applied liberally to all exhaust fasteners and allowing a significant period of time for the chemical to lubricate the threads before attempting to disassemble.
1. On each exhaust pipe behind the catalytic converter, unbolt the clamp (figure 1) using a 15mm socket. Unbend the metal tab (figure 2) on each pipe.
2. Remove (4) cross-brace support bolts using 15mm socket (figure 3). Place hardware to the side.
3. Lubricate all the hangers and rubber isolators.
4. Using a muffler stand or an additional person to hold the rear muffler into position, remove the hangers from the rubber isolators (figure 3) and at each rear muffler.
(more…)

• 0 Comments

With a used vehicle, we suggest a penetrating spray lubricant to be applied liberally to all exhaust fasteners and allowing a significant period of time for the chemical to lubricate the threads before attempting to disassemble.
1. Carefully disconnect and remove the oxygen sensors located just behind each front flange as the left side shown in figure 1. Place them to the side for use during the installation of your new exhaust system.
2. Unbolt and remove the center support bar shown in figure 2. Place the hardware to the side for use during the installation of your new exhaust system.
(more…)

• 0 Comments

Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing a Borla Performance Exhaust System on your vehicle will eliminate the restrictive design of the stock exhaust, allowing your engine to discharge exhaust gas easier. The result is more horsepower and torque, longer engine life, and a distinctive throaty growl- all this, with easy bolt-on installation. These installation instructions have been written to help you in the installation of your Borla Performance Exhaust System. Please read it completely before installing your system.
(more…)

• 0 Comments

The Jet Performance Module is designed to enhance the performance and drivability of your vehicle. By optimizing the air/fuel ratio, ignition advance and various other parameters. The Jet Module retunes your engine for maximum performance.
JET STAGE 1 MODULE:
The Jet Stage 1 Module is optimized for stock vehicles. Minor bolt on modifications such as free flow air filters and cat back exhaust systems will work with the stage 1 tuning. Premium fuel is recommended for best performance gains, but for normal light driving, lowgrade or midgrade fuels may be used.
JET STAGE 2 MODULE:
The Jet Stage 2 Module is optimized for modified vehicles. The stage 2 requires premium fuel and the use of a Jet 180 degree thermostat. We also recommend a cat back exhaust system. The stage 2 will work well with headers, free flow air intake systems and filters.
(more…)

• 0 Comments