1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable.
2. Disconnect the air temperature sensor electrical connection.
3. Pull firmly up on the engine cover to remove.
4. Loosen the hose clamps on the air intake tube at the throttle body and air box.
5. Disconnect the crank case vent from the valve cover.
6. Remove the air intake hose and crank case vent from vehicle.
7. Lift firmly up on the air box to remove from the car.
8. Remove the stock air box grommets from the stock air box mounting tray.
(more…)

• 0 Comments

1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable.
2. Depress the locking tab on the mass air sensor electrical connection, then disconnect the\ mass air sensor electrical connection as shown.
3. Release the locking tab and disconnect the crank case vent tube as shown.
4. Loosen the hose clamp, which secures the intake tube to the throttle body, and release the air box over center clips shown.
5. Remove the air box housing half and intake tube as shown.
6. Remove the three body support brace mounting bolts shown and then remove the support brace from the engine compartment.
NOTE: It will be necessary to unhook the cruise control and wiring harness clips from the body brace.
(more…)

• 0 Comments

1. Turn off the ignition and disconnect the negative battery cable.
2. Depress the locking tab and then disconnect the Mass air sensor electrical connection.
3. Loosen the hose clamp which secures the stock intake tube to the turbo inlet tube.
4. Disconnect the stock intake tube from the turbo inlet tube and then lift the complete stock intake assembly from the vehicle as shown.
NOTE: K&N recommends that customers do not discard factory air intake.
(more…)

• 0 Comments

TO START the Installation:
1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable.
2. Remove the four 13mm nuts that secure the strut toner brace to vehicle, then remove brace from vehicle.
3. Squeeze the two locking tabs together, then remove the mass air electrical connection as shown.
4. Loosen the hose clamp at the intake plenum and release the two clips that secure the air box lid to vehicle, then remove the upper air box and intake tube as shown.
(more…)

• 0 Comments

1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable.
2. Disconnect the mass air sensor electrical connection.
3. Remove oil cap, then pull up on engine cover to release from its retainers.
4. Disconnect the crank case vent hose from the intake plenum.
5. Loosen the two hose clamps on the intake plenum, then remove the intake plenum from the vehicle as shown.
(more…)

• 0 Comments

The K&N intake tube installation:
1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable.
2. Disconnect the mass air sensor electrical connection.
3. Loosen hose clamp at the mass air, then remove the three 10mm bolts that secure air box to vehicle.
4. Remove air box from vehicle as shown.
(more…)

• 0 Comments

TO START:
1. Turn off the ignition and disconnect the negative battery cable.
2. Disconnect the mass air sensor electrical connection and unhook the mass air sensor wiring from the engine cover.
3. Remove the two screws shown that secure the fresh air tube to the fresh air duct.
4. Pull up firmly on the air filter housing/engine cover assembly to release it from the mounting grommets.
NOTE: The air filter housing/engine cover assembly is still attached to the intake inlet tube.
5. Using pliers, release the spring clamp that secures the intake to the intake inlet. Then unhook the intake tube from the inlet.
(more…)

• 0 Comments

TO START:
1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable.
2. Disconnect the mass air sensor electrical connection.
3. Loosen the hose clamp on the intake tube at the throttle body.
4. Loosen and remove the bolt that secures the air cleaner assembly to the inner fender.
5. Detach the crank case vent hose from the intake tube.
(more…)

• 0 Comments

These instructions provide information for the installation of the 60510 Fuel Injection Wire Harness Kit. The contents of these instructions are divided into major Sections, as follows:
1.0 Introduction
2.0 About These Instructions
3.0 Tools Needed
4.0 Pre-Installation and Harness Routing Guidelines
5.0 General Installation Instructions
6.0 60510 & 60511 Fuel Injection Harness Kit
7.0 Start Up
8.0 Trouble Shooting Instructions and Trouble Codes
(more…)

• 0 Comments