Before beginning this installation, please read through this entire instruction booklet and the Street Supercharger System Owner’s Manual (Race Owner’s Manual for the Renegade kit) which includes the Limited Warranty Program, the Warranty Registration form and return envelope. Vortech supercharger systems are performance improving devices. In most cases, increases in torque of 30-40% and horsepower between 45-55% can be expected with the boost levels specified by Vortech Engineering. This product is intended for use on healthy, well maintained engines. Installation on a worn-out or damaged engine is not recommended and may result in failure of the engine as well as the supercharger. Vortech Engineering is not responsible for engine damage. Installation on new vehicles will not harm or adversely affect the break-in period so long as factory break-in procedures are followed.
(more…)

• 0 Comments

The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Owner‘s manual handy, so you can refer to it at any times manual is considered a permanent part of the engine and should 1 the engine if resold. Specifications included in this publication were in effect of approval for printing. Illustrations are based on the GX270. Only type is equipped for both electric and manual starting. Honda Motor sen/es the right, however, to discontinue or change specifications at any time without notice and without incurring any obligation No part of this publication may be reproduced without written
(more…)

• 0 Comments

Service at the indicated distance or time, whichever comes first. Use this schedule if the vehicle is driven MAINLY in Canada or in any of the following conditions; if only OCCASIONALLY driven in these conditions, use the Normal Conditions schedule.
Severe Driving Conditions
- Less than 5 miles (8 km) per trip or, in freezing temperatures, less than 10 miles (16 km) per trip
- In extremely; hot weather (over 90°F/32°C)
- Extensive idling or long periods of stop-and-go driving
- Trailer towing
- On muddy, dusty, or de-iced roads
(more…)

• 2 Comments

Maintenance Nissan for 15.000 KM:
ENGINE MAINTENANCE (Petrol Engine)
Replace engine oil
Replace engine oil filter
Inspect drive belts
Inspect cooling system
(more…)

• 0 Comments

The lamp illustrated is an oil level low warning indicator and not a service interval indicator. When the engine oil is at the correct level, this lamp will automatically extinguish. Malfunction Indicator Lamp (MIL) The lamps illustrated above, are Malfunction Indicator Lamps (MIL) and not service interval indicators. When illuminated there is a problem with the vehicle. Refer to manufacturer’s documentation for further information.
(more…)

• 0 Comments

When repairing the oil pump, the oil pan and strainer should be removed and cleaned. 1. REMOVE CRANKSHAFT TIMING PULLEY (See page EM–13) 2. 4WD: REMOVE FRONT DIFFERENTIAL (See page SA–47) 3. DRAIN ENGINE OIL 4. A/T: REMOVE OIL COOLER TUBE AND CLAMP (A340E: See page AT–24) (A340F: See page AT–30) 5. REMOVE REAR END COVER AND DUST COVER 6. DISCONNECT STARTER WIRE CLAMP 7. REMOVE CRANKSHAFT POSITION SENSOR 8. REMOVE OIL PAN (a) Remove the 17 bolts and 2 nuts. (b) Using SST and a brass bar, separate the oil pan (more…)

• 0 Comments

REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE OIL 3. 4WD: REMOVE FRONT DIFFERENTIAL AND DRIVE SHAFTS ASSEMBLY 4. REMOVE DRIVE BELT FOR GENERATOR, FAN WITH FLUID COUPLING AND WATER PUMP PULLEY (See page CO–5) 5. REMOVE CYLINDER HEAD ASSEMBLY (See page EM–34) 6. DISCONNECT A/C COMPRESSOR AND BRACKET (a) Remove the 4 bolts, and disconnect the compressor from the bracket. HINT: Put aside the compressor, and suspend it. (b) Remove the 4 bolts and A/C compressor bracket. 7. REMOVE GENERATOR, ADJUSTING BAR AND BRACKET (a) Disconnect the generator connector. (b) Remove the nut, and disconnect the generator wire and wire clip. (c) Remove the lock bolt, pivot bolt and generator. (d) Remove the bolt and adjusting bar. (e) Remove the 3 bolts and generator bracket. 8. (more…)

• 0 Comments

Crankcase emission control equipment is separated into two different systems: Positive
Crankcase Ventilation (PVC) and Crankcase Ventilation System (CCV). The systems perform
the same function, differing only in the way the exhaust gases are metered. The PVC system uses
a valve, containing spring loaded plunger, which meters the amount of crankcase vapors routed
to the combustion chamber based on manifold vacuum. The CCV system contains a metered
orifice of a calibrated size which meters the amount of crankcase vapors drawn from the engine
based on manifold vacuum.
(more…)

• 0 Comments

REMOVAL & INSTALLATION the GM Full-Size Trucks Fuel Injectors
1. Disconnect the negative battery cable.
2. Relieve the fuel system pressure.
3. Disengage the fuel meter body electrical connection and the fuel feed and return hoses from the engine fuel pipes.
4. Remove the upper manifold assembly.
5. Tag and remove the poppet nozzle out of the casting socket.
6. Remove the fuel meter body by releasing the locktabs. Each injector is calibrated. When replacing the fuel injectors, be sure to replace it with the correct injector.
(more…)

• 0 Comments

This pdf covers the removal & installation the timing case cover for Chevrolet S10 Pickup.
Removal
1. Disconnect negative battery cable. Remove P/S reservoir from radiator shroud. Remove upper fan shroud. Remove serpentine belt.
2. Remove generator with brackets and lay aside. Using Hub Puller (J-24420-B), remove crankshaft pulley hub. Remove oil pan. See OIL PAN. Remove front timing case cover bolts, and cover.
3. Using large screwdriver, remove crankshaft front seal. DO NOT distort timing gear cover during seal removal.
CAUTION: To prevent oil leakage, coat crankshaft pulley hub keyway with RTV sealant before installation.
(more…)

• 0 Comments