The GMRC-03 is designed to be used in Cadillac’s that do not have Onstar or amplified systems. It will retain the warning chimes that are lost when the factory radio is removed. The GMRC-03 will also provide a 12 volt switched accessory wire for proper radio operation. *Note: The GMRC-03 can be used in Cadillac’s that come with a factory amplifier; however the factory amplifier must be bypassed and the speaker wires on the GMRC-03 must not be used. Running new wires to the speakers is recommended. If the Cadillac also has Onstar, that feature will be lost.
(more…)

• 0 Comments

The GM20SR is a plug and play interface that allows replacement of a General Motors Class II factory stereo in Cadillac CTS and SRX vehicles. It will maintain operation of the OnStarо and factory amplified systems. The GM20SR has on board switching to allow audio from the OnStarо system to play through the two front factory speakers when OnStarо is active. It also retains warning chimes for Onstarо operation. For additional vehicle integration, use Scosche’s line of SWC-1 steering wheel controls (SWC) interfaces to retain SWC’s with the aftermarket radio. Also retains Vehicle Parking Assist chimes.
(more…)

• 0 Comments

The PESWICAN module must be used with an optional Steering Wheel Interface module like the PESWIX, PESWIAKJC, PESWIPS or PESWIECL to retain steering wheel controls. For select Chrysler vehicles listed. The CHYAH05 interface module is recommended but is not needed when being used in a Chrysler vehicle. If you do not need an CHYAH05 interface, you can hard wire the PESWICAN to any aftermarket vehicle harness listed in this application guide. Details on how to wire the PESWICAN are in the instructions.
(more…)

• 0 Comments

Installation:
The CHYX plugs into the back of the factory radio.
1. Remove factory radio. Remove factory female 10 pin Satellite cable, if available. Plug the CHYX’s 10 pin SAT plug into the radio. Plug the factory Satellite cable that was just removed into into the CHYX’s 10 pin connector.
2. Insert the CHYX’s 22 pin main power Plug (T-Harness) in between the factory radio and factory harness.
3. Connect external audio devices(s) into Aux 1 and/or Aux 2 inputs using the RCA jacks on the CHYX.
4. If the vehicle has both factory Satellite and VES, you must disconnect either one directly at the device. If the vehicle has factory single disc radio, the Satellite receiver must be disconnected directly at the device . Refer to vehicle’s repair manual for location and removal of the Satellite receiver or VES plug.
(more…)

• 0 Comments

Installation:
If the vehicle has a VES (Video Entertainment System), it must be disconnected! This interface is not compatible with REF model radios. They do not have a VES input available.
1. Remove factory radio. Remove factory female 10 pin Satellite cable, if available. Plug the CHYP’s 10 pin SAT plug into the radio. Plug the factory Satel- lite cable that was just removed into the CHYP’s 10 pin connector.
2. Insert the CHYP’s 22 pin main power Plug (T-Harness) in between the factory radio and factory harness.
(more…)

• 0 Comments

Using Audi-specific radio removal keys, remove the radio from the dash by pulling toward you after the four locks have been disengaged. The radio fits very tightly into the opening even when the locks are released. Disconnect all plugs from the back of the factory radio, remove and set aside. MAKE SURE THAT YOUR RADIO IS NOT CODED OR THAT YOU HAVE THE CODE BEFORE
(more…)

• 0 Comments

The GROM iPod adapter is designed to provide endless hours of listening pleasure through most vehicles factory radio. To insure that your iPod performs correctly in your car or truck, we recommend that you read this entire manual before attempting install the GROM interface.

Proper mounting location
Securely install the interface in a location free from; heat, humidity, moving parts or direct sunlight. Beware of hot-air flow from your vehicle’s climate control system. We recommend securing the interface to a suitable location, free of sharp metal edges, using double sided tape, Velcro or wire ties.
(more…)

• 0 Comments