The AEM Engine Management System (EMS) is the result of extensive development on a wide variety of vehicles. Each system is engineered for a particular application. The AEM EMS differs from all others in several ways. The EMS is a “stand-alone”, which completely replaces the factory ECU and features unique plug and play technology. There is no need to modify the factory wiring harness and in most cases the vehicle may be returned to stock in a matter of minutes. The AEMPro software is configured to work with the factory sensors and equipment, so there is no need for expensive or hard to find sensors, making replacements and repairs as simple as with any stock vehicle. For stock and slightly modified vehicles, the AEMPro software can be programmed with base parameters, providing a solid starting point for beginner tuning. For more heavily modified cars, the EMS has many spare inputs and outputs allowing the elimination of add-on rev-limiters, boost controllers, nitrous controllers, fuel computers, etc. It also includes a configurable onboard data logger capable of recording 512kb of information. Every EMS comes with all functions installed and activated, and there are no expensive options or upgrades to be performed.
(more…)

• 0 Comments

The installation of the AEM ECU on the 2000-2003 Mitsubishi Eclipse/Lancer uses the stock sensors and actuators. The base map is automatically installed in the base calibrations directory in the AEMPro directory on your computer. It is named either 1312 Lancer.v1.00.cal or 1312 Eclipse.v1.00.cal.
Full details of the test vehicle used to generate this map can be found in the files notes section. However, while the base map is a good starting point and may save you considerable time and money, it will not replace the need to tune your specific application. It is not intended to be driven aggressively. Ignoring this can and will damage your engine.
(more…)

• 0 Comments

1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the radio trim panel including the a/c vent. (Figure A) 3 Remove (4) 10 MM bolts securing the radio. Unplug and remove the radio.
DOUBLE DIN RADIO PROVISION STACKED ISO MOUNT UNITS
*Note: Refer also to the instructions included with the aftermarket radio.
1 Snap the Double DIN Trim plate into the rear of the factory radio trim panel. (Figure A)
DOUBLE DIN RADIO PROVISION STACKED ISO MOUNT UNITS PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
(more…)

• 0 Comments

1. Disconnect the negative battery terminal to prevent an accidental short circuit.
2. Unclip and remove the center console trim panel. (Figure A)
3. Unclip the center dash trim panel.
4. Remove (4) screws securing the radio. Disconnect and remove the radio.
5. Remove (3) screws securing the radio rear support bracket and remove the bracket.
(more…)

• 0 Comments

The Jet Performance Module is designed to enhance the performance and drivability of your vehicle. By optimizing the air/fuel ratio, ignition advance and various other parameters. The Jet Module retunes your engine for maximum performance.
JET STAGE 1 MODULE:
The Jet Stage 1 Module is optimized for stock vehicles. Minor bolt on modifications such as free flow air filters and cat back exhaust systems will work with the stage 1 tuning. Premium fuel is recommended for best performance gains, but for normal light driving, lowgrade or midgrade fuels may be used.
JET STAGE 2 MODULE:
The Jet Stage 2 Module is optimized for modified vehicles. The stage 2 requires premium fuel and the use of a Jet 180 degree thermostat. We also recommend a cat back exhaust system. The stage 2 will work well with headers, free flow air intake systems and filters.
(more…)

• 0 Comments

Thanks again for purchasing your new 409 stainless steel Pypes Performance Exhaust Ford Mustang off-road or street legal x-pipe. Please be sure to confirm all the components in the kit were received in your shipment before beginning installation. All kits will include your new x-pipe with 02 bungs, installation hardware, and header sleeves (if required). If you purchased a street legal version, you should have also received a CVM10K or CVM11K cat kit. If you purchased XFM16, you received (1) small sleeve for the drivers side leg. If you purchased XFM19, both mounting points at the headers require the (2) small sleeves supplied. If you find any component missing, please contact our office at 800-421-3890 for replacement.
(more…)

• 0 Comments