Step 1. Remove the contents from the box and check for any damage. Verify all parts against the parts list.
Step 2. Read and understand instructions completely before beginning installation.
Step 3. To assemble the grille guard, position the center section. The bottom side of the center section is the longer end. Insert wings so that the wing slot lines up with the center section hole. Attach uprights to grille guard through top holes (more…)

• 0 Comments

Installation Stainless Steel Oval on Dodge RAM HD Crew Cab:
1. Read instructions completely and check to make sure that all required parts (listed on service parts list) are on hand before starting the installation.
2. Oval step assemblies and brackets (item #1 & 2) are pre-assembled.
2.1. The front and rear mounting brackets on these assemblies are rotated for shipping purposes. These brackets must be rotated to the vertical position and the ‘/2″ bolts. Torque to 65 lb ft.
(more…)

• 0 Comments

The mounting procedure outlined below covers CHEVROLET (1988 – 2000), and 1 ton trucks. You will need to refer to the illustrations and familiarize yourself with each of the undercarriage components and their relative position to each other. Then proceed as follows:
1. Position the PUSH BEAM SUPPORT PLATES (Ref. 62A and 62B, Fig. 1) to the front frame rails of the truck. If the truck is equipped with tow hooks, remove the tow hook bolts, and tow hook before installing the PUSH BEAM SUPORT PALTES. Using M14 x 2.00 Hex Head Bolts and M14 Lock Washers provided, bolt the PUSH BEAM SUPPORT PLATES through the outside of the frame. Next use ―” – 13 x 1- ―” Hex Head Bolts, ―” Flat Washers, and ―” – 13 Hex Head Self Locking Nuts to bolt the PUSH BEAM SUPPORT PLATES through the bottom of the frame. Tow hooks may be relocated under the PUSH BEAM SUPPORT PLATES and reattached. Fasteners should only be finger tight.
(more…)

• 0 Comments

This suspension kit consists of all parts necessary to make a successful installation onto your Vehicle. All parts have been tested thoroughly. Please make sure you take all necessary safety precautions while fitting the kit.
Note: you should first read these instructions carefully and then take all parts out of the box and pre-assemble them as far as possible before fitting them onto your vehicle.
(more…)

• 0 Comments

Instructions Procedure:
1. Before beginning the installation, please read all directions carefully and verify that all necessary hardware is accounted for. If any parts are missing, stop the installation and contact your distributor immediately.
NOTE: The center channel/tube is installed in the lower position, if you install a winch higher than 11″ you can raise the central channel/tube to the next holes position.
2. If vehicle has factory tow hooks you must remove them. If vehicle has not factory tow hooks you must remove the plastic cover from the bumper. Image 1. NOTE: Tow hooks or plastic cover will not be reinstalled.
3. Locate the nuts and studs that secure the bumper bracket to the frame rail. Remove the (2) lower nuts.
(more…)

• 0 Comments

The mounting procedure outlined below covers the 2000 – 2004 Dodge Dakota trucks. You will need to refer to the illustrations and familiarize yourself with each of the undercarriage components and their relative position to each other. Then proceed as follows:
1. Disconnect fog lamps from bumper if equipped on vehicle.
2. Cut rubber portion of air deflector attached to bumper and discard. Open vehicle hood and remove four vertical bumper bolts from existing Bumper Brackets (BB). Remove bolts from two outer bumper brackets if equipped on vehicle. Remove bumper.
3. Clamp existing Bumper Bracket (BB) to frame rail. Remove two existing Nuts (AA) from Bumper Bracket (BB). Use chisel and hammer between head of existing Bolts (CC) and Bumper Bracket (BB) to force them loose. Use caution to prevent damage to parts. Unclamp and remove Bumper Bracket (BB). Repeat process on opposite side of vehicle.
(more…)

• 0 Comments

All instructions are written from the drivers seat position looking forward at the vehicle dash. We advise caution whenever your removing or handling plastic parts of a vehicles dash. WARNING: Unnecessary force or pressure can cause pieces to crack or break.
Locate four slots on the face of the radio. Insert four Audi DIN tools in these four slots until you hear or feel the tools click or lock.
(more…)

• 0 Comments