Installation of this baseplate requires drilling 17/32” holes in the vehicle’s frame.
1. Read the General Instruction Sheet included with this baseplate.
2. The baseplate bolts to the bottom of the frame behind the bumper using six bolts supplied with the baseplate. Use of Loctite to secure the bolts is highly recommended. The vibrations and stresses of towing can cause bolts to loosen even with lock washers in the assembly.
(more…)

• 0 Comments

Note on Sport Model Trucks – This light bar will not mount correctly on sport model trucks without realigning the bumper. TRUCKS WITH FACTORY TOW HOOKS
1. Temporarily remove the factory tow hooks and set them aside along with the bolts.
2. Position your KC light bar so the brackets will sandwich between the tow hooks and the frame. ( NOTE – The light bar must be rolled into Bumper place by inserting the lower end of the brackets into the opening first Bolts and then rolling it up into place.)
(more…)

• 0 Comments

Start by removing the factory pillar. This is done by pulling down the rubber door gasket and removing the two screws in the handle area of the pillar, tip the top towards the steering wheel to get it out. You have to use a little force to get it free of the dash.
Though the gauge pod is intended to be used as a replacement for the factory pillar, we suggest cutting the handle off of the factory pillar and using the gauge pod as a cover. This is so that the backs of the gauges will not be visible through the windshield after installation.
(more…)

• 0 Comments

Installation steps this Moonroof visor on 2005 CRV:
1. Clean and wax the area to be covered with a high-quality paste wax.
2. Open the moonroof.
3. Using isopropyl alcohol on a shop towel, clean the areas where the EPT sealer will attach.
4. Remove the adhesive backing from the EPT sealer, and attach it to the roof in the area shown.
5. Insert a Phillips-head screw through each of the holes on the top of the visor; loosely install the clips and self-locking nuts.
(more…)

• 0 Comments

INSTALLATION
NOTE: Be careful not to damage the tailgate and the body paint finish.
1. Open the tailgate. Insert a flat-tip screwdriver into the specified position of the right tailgate trim, and remove the pin as shown.
2. Remove the clip and remove the right tailgate trim.
3. Remove the left tailgate trim in the same manner.
4. Align the template with the left edge of the tailgate, and the front edge of the tailgate. Hold the template in place using masking tape. Mark the tailgate through the template using a felt-tip pen. Remove the template.
(more…)

• 0 Comments

It is recommended to have a wiring schematic of your vehicle’s ignition system to clearly identify the Coil Positive (12 Volt ) supply wiring.
The MSD Tach Driver wires inline on the positive 12 volt supply wire. It senses current on the coil positive wire and converts it to a 12 volt signal output. To install the Tach Driver, the coil positive wire must be identified for your application. Once the wire has been located it is recommended to check for 12 volts using a volt meter. Connect the meter and turn the ignition On. In some cases, the engine must be cranked over in order to see 12 volts.
(more…)

• 0 Comments

Installation: 2002 Taurus
This siren will be mounted onto the vehicle horn’s mounting plate near the drivers side front tire. The vehicle horn’s mounting holes will be used to mount the SA314 siren speaker.
WARNING! Loud siren noise can cause hearing loss. Minimize exposure. Close windows when using.
1. Since the siren will be mounted upside down, its drain hole is now on top. This requires another drain hole to be drilled into the siren before mounting (See “Drilling the drain hole”).
2. Mount siren onto the bracket using the supplied mounting hardware. Install a spacer nut onto each of the bracket’s Pem Studs (Fig. 2).
3. Remove the large (full vehicle width) plastic splash guard mounted to the front, underside of the vehicle (Fig. 1). This allows access to the vehicle horn.
(more…)

• 0 Comments

STEP 1: The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in the shape as shown in the photos above. For more information on how to remove the radio, see the diagram below.
STEP 2: Pull the radio from the dash. Unplug the antenna cable from the rear of the radio. Unplug the 2 wire harness connectors from the rear of the radio.
(more…)

• 0 Comments

Instructions: There are four M10 countersunk bolts supplied with this kit.
2 x M10 x 40 (Standard Thread)
2 x M10 x 1.25 x 40 (Fine Thread)
These bolts are used to mount the upper brackets to the chassis. When the bump stop is removed the threaded hole must be examined to determine if it is a standard or fine thread.
(more…)

• 0 Comments

The Mudguards installation steps on Toyota Rav4 Flared
1. Clean Front Mounting Area
Clean and degrease front body panel where mudguard is to be located with a clean, dry lint free cloth after use of 3M™ Prep Solvent – 70. When cleaning with 3MTM Prep Solvent-70 follow the manufacturer’s directions. Do not allow cleaner to air dry.
2. Hardware Installation and Removal.
Install supplied plastic insert into square hole location C. (Fig. 2-1). Remove existing screws locations A and B. Do not discard. (Fig.2-1)
3. Installation of Front Mudguard (a) Mount mudguard on body panel and reinstall existing screws in locations A and B while holding part up and tight against body. (Fig. 3-1).
(more…)

• 2 Comments