The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Owner‘s manual handy, so you can refer to it at any times manual is considered a permanent part of the engine and should 1 the engine if resold. Specifications included in this publication were in effect of approval for printing. Illustrations are based on the GX270. Only type is equipped for both electric and manual starting. Honda Motor sen/es the right, however, to discontinue or change specifications at any time without notice and without incurring any obligation No part of this publication may be reproduced without written
(more…)

• 0 Comments

This Rider’s Manual will provide you with an initial overview of your motorcycle. All maintenance and repair work on the motorcycle is documented in Chapter 11. This record of the maintenance work you have had performed on your motorcycle is a precondition for generous treatment of goodwill claims. When the time comes to sell your BMW, please remember to hand over this Rider’s Manual; it is an important part of the motorcycle.
(more…)

• 0 Comments

This Z3 Hardtop Use & Install manual serves as a supplement to the owner’s manual for your vehicle. Keep it safely together with your other vehicle papers. Please refer to the owner’s manual for your vehicle or to the corresponding supplementary owner’s manual for on other items of vehicle. Your BMW service centre you with any queries engineering and high level of quality of BMW equipment is ensured therefore possible that discrepancies occur between this supplementary uni in! on-”* *^o er your vehicle. We cannot exclude a!! errors either and in this we would ask for your understanding so that no legal claims may be brought deriving from the data, illustrations and descriptions in this (more…)

• 2 Comments

Due to differences in manufacturing, dimensions and inflated measurements, tire and wheel combinations should be test fit prior to installation. Tire and wheel choice is crucial in assuring proper fit, performance, and the safety of your Pro Comp equipped vehicle. For this application, a wheel not to exceed 10” in width with a minimum backspacing of 3.25” must be used. Additionally, a quality tire of radial design, not exceeding 33” tall X 12.5” wide is recommended. Please note that the use of a 33” X 12.5” tire may require fender modification. Violation of these recommendations will not be endorsed as acceptable by Pro Comp Suspension and will void any and all warranties either written or implied.
(more…)

• 0 Comments

The mounting procedure outlined below covers the 1997-2002 Jeep Wrangler. Note that a
Front Gross Axle Rating (FGAWR) of 2500 lbs. is required. A suspension upgrade and additional
ballast may be necessary. You will need to refer to the illustrations and familiarize yourself with each
of the undercarriage components and their relative position to each other. Then proceed as follows:
Begin by removing the four screws that hold the plastic “Jeep” valance in place above the
bumper. Keep these screws as they will need to be reinstalled.
(more…)

• 0 Comments

The mounting procedure outlined below covers CHEVROLET (1988 – 2000), and 1 ton trucks. You will need to refer to the illustrations and familiarize yourself with each of the undercarriage components and their relative position to each other. Then proceed as follows:
1. Position the PUSH BEAM SUPPORT PLATES (Ref. 62A and 62B, Fig. 1) to the front frame rails of the truck. If the truck is equipped with tow hooks, remove the tow hook bolts, and tow hook before installing the PUSH BEAM SUPORT PALTES. Using M14 x 2.00 Hex Head Bolts and M14 Lock Washers provided, bolt the PUSH BEAM SUPPORT PLATES through the outside of the frame. Next use ―” – 13 x 1- ―” Hex Head Bolts, ―” Flat Washers, and ―” – 13 Hex Head Self Locking Nuts to bolt the PUSH BEAM SUPPORT PLATES through the bottom of the frame. Tow hooks may be relocated under the PUSH BEAM SUPPORT PLATES and reattached. Fasteners should only be finger tight.
(more…)

• 0 Comments

The mounting procedure outlined below covers the 2003 and Newer ū & 1 Ton Dodge trucks. You will need to refer to the illustrations and familiarize yourself with each of the undercarriage components and their relative position to each other. Then proceed as follows:
1. Remove the mounting hardware connecting the bumper to the driver side of the frame. Align the two vertical holes on Push Beam Support Plate (62B) with the bumper mounting holes on the outside of the frame. Attach Push Beam Support Plate (62B) to the frame using ―”-13 x 4-―” Hex Head Bolt (G) and ―”-13 Lock Nut (B). The rear and bottom mounting holes on Push Beam Support Plate (62B) must be drilled in the truck frame. With Push Beam Support Plate (62B) in place, drill two 9/16” diameter holes in the truck frame. Drill the hole in the side of Push Beam Support Plate (62B) through both walls of the frame. Drill the bottom hole through the bottom frame wall only. Repeat the process on the passenger side.
(more…)

• 0 Comments

The mounting procedure outlined below covers the 2000 – 2004 Dodge Dakota trucks. You will need to refer to the illustrations and familiarize yourself with each of the undercarriage components and their relative position to each other. Then proceed as follows:
1. Disconnect fog lamps from bumper if equipped on vehicle.
2. Cut rubber portion of air deflector attached to bumper and discard. Open vehicle hood and remove four vertical bumper bolts from existing Bumper Brackets (BB). Remove bolts from two outer bumper brackets if equipped on vehicle. Remove bumper.
3. Clamp existing Bumper Bracket (BB) to frame rail. Remove two existing Nuts (AA) from Bumper Bracket (BB). Use chisel and hammer between head of existing Bolts (CC) and Bumper Bracket (BB) to force them loose. Use caution to prevent damage to parts. Unclamp and remove Bumper Bracket (BB). Repeat process on opposite side of vehicle.
(more…)

• 0 Comments

Installation Instructions:
1. Refer to the illustrations and location chart for correct size shift cups.
2. Using a T20 Tork Plus bit, remove the existing OEM plastic shift cup and discard.
3. Using a T20 Tork Plus bit, install the correct size replacement aluminum shift cup.
4. Make sure the replacement shift cup is properly rotated so that the tabs will retain the valve body components securely.
(more…)

• 0 Comments

These installation instructions are mainly intended for use in the MINI dealership network and by authorised BMW Service Centres. The target group of these installation instructions are technical personnel trained on MINI vehicles with corresponding technical know-how.
All work is to be carried out with the aid of currently valid MINI repair instructions, schematic circuit diagrams, maintenance manuals and working instructions in rational order with the specified tools (special tools) while paying particular attention to valid safety regulations.
(more…)

• 0 Comments