- Locate rear bumper attachment point on driver side.
- Remove bumper fasteners.
- Install mounting bracket onto linkage as shown. Torque to 33 ft-lbs / 44 Nm.
NOTE: 2500, 3500 HD trucks do not use spacer ( 5 ). Use fastener ( 2 ) on HD trucks.
- Slide upper mount over factory studs, install fasteners and torque to 70 ft-lbs / 95 Nm.
- Install step pad assembly onto linkage assembly with two socket cap screws.
- Adjust step pad position side to side. Allow for foot access. Torque allen head bolts to 10 ft-lbs / 13.5 Nm.
(more…)

• 0 Comments

Installation steps this Moonroof visor on 2005 CRV:
1. Clean and wax the area to be covered with a high-quality paste wax.
2. Open the moonroof.
3. Using isopropyl alcohol on a shop towel, clean the areas where the EPT sealer will attach.
4. Remove the adhesive backing from the EPT sealer, and attach it to the roof in the area shown.
5. Insert a Phillips-head screw through each of the holes on the top of the visor; loosely install the clips and self-locking nuts.
(more…)

• 0 Comments

Kit Contents: 1. DICE Module 2. Audi radio interface cable (vehicle specific cable) 3. Docking Cable
Installation Steps for this kit
1. Pull vehicle into service bay and access trunk area.
2. Disconnect both battery terminals. These cables must be disconnected during installation to insure proper initialization of the DICE module when the DICE when it is connected.
3. Remove radio by inserting the (4) factory keys (not included) into the slots on each corner of the radio.
4. CD changer interface will be on left hand side of radio, it is the smaller left-hand connector on the bottom of the harnesses. Remove all wiring from the radio unit and remove from vehicle.
(more…)

• 0 Comments

For bolts into aluminum, use light oil, or anti-seize, not Loctite! For bolts into the steel bracket, use Loctite.
Check for free movement of the lever and pulley after bolting to the bracket! If the lever sticks at any point in it’s travel, check the bracket for any weld spatter, or plating material, and use a Dremel to smooth the area. If the pulley pin is rubbing, it may be pressed in too far. Support the back side of the pulley, and press or tap it in with a hammer, until it has clearance.
(more…)

• 0 Comments

Installation Steps:
• A floor mat anchor prevents the front floor mat from sliding forward and possibly interfering with the pedals.
• If you remove the front floor mat, make sure you re-anchor it when you put it back in your vehicle.
• If you replace the floor mat, use factory floor mats designed to be used with the floor mat anchor.
• If you use a non-factory floor mat in the driver’s foot well, make sure it fits properly and that it can be used with the floor mat anchors.
• Do not put additional floor mats on top of the anchored mat, otherwise the additional mats may slide forward and possibly interfere with the pedals.
(more…)

• 0 Comments

The Mudguards installation steps on Toyota Rav4 Flared
1. Clean Front Mounting Area
Clean and degrease front body panel where mudguard is to be located with a clean, dry lint free cloth after use of 3M™ Prep Solvent – 70. When cleaning with 3MTM Prep Solvent-70 follow the manufacturer’s directions. Do not allow cleaner to air dry.
2. Hardware Installation and Removal.
Install supplied plastic insert into square hole location C. (Fig. 2-1). Remove existing screws locations A and B. Do not discard. (Fig.2-1)
3. Installation of Front Mudguard (a) Mount mudguard on body panel and reinstall existing screws in locations A and B while holding part up and tight against body. (Fig. 3-1).
(more…)

• 2 Comments

This performance kit installation steps on Audi A3: 1. Disconnect the negative terminal from the vehicle battery. 2. Remove the plastic engine cover. (Fig. 1) 3. Unclip & remove the engine breather hose from the intake pipe. (Fig. 2) 4. Remove the small vacuum hose from under the breather hose on the intake pipe. Follow the vacuum hose & remove the hose from the inlet manifold. Blank off the pipe on the manifold using the small rubber cap supplied. (Fig. 3) 5. Remove the small rubber hose from the side of the intake pipe as shown. (Fig. 4) 6. Unclip & remove the auxiliary air pump feed pipe from the air box as shown. (Fig. 5) 7. Unclip & remove the plastic intake pipe from the throttle housing. (Fig. 6) 8. Remove the air box securing bolt & carefully pull the air box assembly out of its mounting grommets. Remove the air box (more…)

• 0 Comments