2003-2004 (KJ) Jeep® Liberty NOTE: This notification applies only to the above vehicles equipped with Remote Keyless Entry (Sales Code GXM) built from April 1, 2003 through December 12, 2003 (MDH 0401XX through 121200).
The rear flip-up window switch on about 120,000 of the above vehicles may be improperly sealed and could allow water to enter into the switch. This can cause the flip-up window to open unintentionally if it is left unlocked. The rear flip-up window switch must be replaced on all affected vehicles.
(more…)

• 0 Comments

Kit parts are prefaced by the word kit and appear in bold print. 1. Carefully read all warnings and instructions completely before beginning.
2. Verify all parts have been received in this kit by checking the parts list at the end of this document.
3. Only install this kit on the vehicle for which it is specified. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-3175.
4. Park vehicle on a clean, dry, flat, level surface and block tires so vehicle cannot roll in either direction. Adhere to recommendations when replacement fasteners, retainers and keepers are called out in the factory service manual. When re-assembling the vehicle it is recommended (more…)

• 1 Comment

The mounting procedure outlined below covers the 1997-2002 Jeep Wrangler. Note that a
Front Gross Axle Rating (FGAWR) of 2500 lbs. is required. A suspension upgrade and additional
ballast may be necessary. You will need to refer to the illustrations and familiarize yourself with each
of the undercarriage components and their relative position to each other. Then proceed as follows:
Begin by removing the four screws that hold the plastic “Jeep” valance in place above the
bumper. Keep these screws as they will need to be reinstalled.
(more…)

• 0 Comments

Installation of a Performance Accessories suspension lift kit will change the center of gravity and the handling characteristics of the vehicle. Because of the higher center of gravity and larger tires, the vehicle will handle and react differently both on and off road. You must drive it safely! Extreme care must be taken to prevent vehicle rollover or loss of control, which could result in serious injury or death. Avoid sudden sharp turns or abrupt maneuvers and always make sure all vehicle occupants have their seat belts fastened.
(more…)

• 0 Comments

WIRING OVERVIEW
Switch Settings (read below for explanation)
Selecting The Vehicle Type
Switches 1,2, and 3 are used to select vehicle type. Use the chart on the back of these instructions to determine which of the above switch settings you will need.
(more…)

• 0 Comments

1. Disconnect the negative battery cable. Loosen the hose clamp on air cleaner box lid. Twist and remove breather hose from air cleaner box lid. 2. Unhook the two air cleaner lid latches on front of box. 3. Remove the air cleaner box lid by sliding it forward, and then up, and out of the factory intake tube. 4. Remove factory air filter from air cleaner box. 5. Remove, and set aside the oil filler cap. Use caution not to drop anything into engine while cap is off. 6. Carefully lift up on the engine cover (it is held in place by grommets, no bolts) to access the hose clamp (more…)

• 0 Comments

Vehicle preparation:
1. Remove the negative battery cable before installing the cruise control components for safety precautions.
2. Jeep wrangler applications: remove airbag by using (3) trim tool to release metal clips as shown in figure 2. Caution: ensure that battery has been 90 seconds disconnected for more than prior to removal of airbag; failure to heed this warning may result in airbag discharge and may cause serious injury or death.
(more…)

• 0 Comments

Tests/Procedures: 1. Ground the Violet/Yellow wire (disarm circuit) that goes to either front door and the theft alarm module. Have the keys out of the ignition and all doors closed when grounding the wire. This should disarm the theft alarm system and prevent the theft alarm from arming. 2. Check that the interior lights do not stay on due to the wire being grounded. If they do, the illuminated entry relay will need to be removed or another method of disabling the theft alarm will have to be used. 3. Another method if the theft alarm module is faulty would be to disconnect the module and replace the Powertrain Control Module (PCM) with a new one.
(more…)

• 0 Comments

Installation Procedure below:
Front Installation:
1. Secure & properly block the tires of the vehicle on a level concrete or asphalt surface.
2. Raise the front of the vehicle in accordance to the manufactures recommendation & support with jack stands.
3. Remove the front tires / wheels.
4. Remove the upper ball joint nut & separate the upper ball joint from the steering knuckle using a ball joint remover or other suitable tool.
5. Disconnect the lower strut fork at the lower control arm & the lower portion of the strut assembly.(See Photo #1)
6. Remove the air box on the passenger side.
7. Remove the 4 upper strut nuts on the strut tower that holds the strut assembly to the strut tower.
8. Separate the strut fork from the strut assembly & remove the strut from the vehicle.
(more…)

• 0 Comments

Before you begin installing this seat riser, please read all installation instructions and warnings thoroughly. This seat is designed to be used on the model vehicles described above. Use of this riser on any other vehicle or failure to install this seat properly may result in an improperly mounted seat and could result in unexpected movement of the seat and loss of control of the vehicle, thereby placing the occupants of the vehicle and others in a potentially dangerous situation.
(more…)

• 0 Comments