The AEM Brute Force Intake System is the result of extensive development on a wide variety of cars. It is the most advanced short pipe air intake system on the market. Each system is specifically engineered for its particular application. All AEM Brute Force Intake Systems deliver maximum performance gains through the lightweight, all- aluminum, mandrel-bent tubing that is tuned in both length and diameter. The tube (more…)

• 0 Comments

Instructions:
NOTE: DO NOT TIGHTEN ANY CLAMPS UNTIL THE LAST STEP!! Note: you will need to reuse your original tips and clamps for the tips for this system.
1) Support the vehicle in a safe manner, using a shop hoist or frame contact jack stands on a level surface. Remove the old exhaust system behind the converter pipe, where the old system clamps to the converter pipe. Note: you will need to reuse your original factory clamps after the converters, as well as your original factory tips and clamps for the tips. You can remove the old system just by removing the clamps after the converters, and removing the exhaust at the flange after the large dual in/out factory resonator muffler on the driver side, and then (more…)

• 0 Comments

This inlet pipe kit may require the removal and reinstallation of emissions related components. If you are not familiar with the installation and/or the operation of these components then please refer this installation to a qualified professional.
Getting started
Make sure vehicle is parked on a level surface. Set parking brake. Disconnect negative battery terminal. If engine has run within the past two hours let it cool down.
(more…)

• 0 Comments

Instructions
Before removing any parts, park the car on a secure, stable and level surface, loosen (but do not remove) the wheel lug nuts, jack the vehicle up and place the car on four stable jack stands or use a professional vehicle lift. We recommend having two people available for certain steps of the installation.
Front Install Instructions
1. Securely support both front corners of the car.
2. Remove front wheels.
3. Disconnect link on ride height sensor to prevent damage.
4. Disconnect hydraulic suspension line and drain in to pan. Remove line from bulkhead mounting plate
5. Remove the Lower Front shock clevis bolt that attaches the fork of the shock to the lower front control arm.
(more…)

• 0 Comments

The AEM Short Ram Air Intake System is the result of extensive development on a wide variety of cars. It is the most advanced short pipe air intake system on the market. Each system is specifically engineered for its application. All AEM Short Ram Air Intake Systems deliver maximum performance gains through lightweight, all- aluminum, mandrel-bent tubing that is tuned in both length and diameter. The aluminum will not crack in extended use like plastic. The tube length and diameter are matched for each specific engine to give power over a broad RPM range. Unlike plastic systems that use a continually diverging cross-section, we take advantage of the acoustical energy in the inlet duct to promote cylinder filling during the intake valve-opening event.
(more…)

• 0 Comments

The AEM intake system is a performance product that can be used safely during mild weather conditions. During harsh and inclement weather conditions, you must return your vehicle to stock OEM air box and intake tract configuration. Failure to follow these instructions will void your warranty.
1. Preparing Vehicle
a. Make sure vehicle is parked on level surface.
b. Set parking brake.
c. If engine has run in the past two hours, let it cool down.
d. Disconnect negative battery terminal.
e. Do not discard stock components after removal of the factory system.
(more…)

• 0 Comments

Preparing Vehicle
Make sure vehicle is parked on level surface.
Set parking brake.
If engine has run in the past two hours, let it cool down.
Disconnect negative battery terminal.
Raise the front of the vehicle with a jack. Refer to your owner’s manual for proper jack and jack stand placement to properly support vehicle. Support your vehicle using properly rated jack stands before wheel removal or while working under the vehicle.
NEVER WORK UNDER A VEHICLE WITHOUT USING JACK STANDS.
Do not discard stock components after removal of the factory system.
(more…)

• 0 Comments

Proper installation of this kit requires knowledge of the factory recommended procedures for removal and installation of original equipment components. We recommend that the factory shop manual and any special tools needed to service your vehicle be on hand during the installation. Installation of this kit without proper knowledge of the factory recommended procedures may affect the performance of these components and the safety of the vehicle. We strongly recommend that a certified mechanic familiar with the installation of similar components install this kit.
(more…)

• 0 Comments

Kit parts are prefaced by the word kit and appear in bold print. 1. Carefully read all warnings and instructions completely before beginning.
2. Verify all parts have been received in this kit by checking the parts list at the end of this document.
3. Only install this kit on the vehicle for which it is specified. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-3175.
4. Park vehicle on a clean, dry, flat, level surface and block tires so vehicle cannot roll in either direction. Adhere to recommendations when replacement fasteners, retainers and keepers are called out in the factory service manual. When re-assembling the vehicle it is recommended (more…)

• 1 Comment

Installation of a Performance Accessories suspension lift kit will change the center of gravity and the handling characteristics of the vehicle. Because of the higher center of gravity and larger tires, the vehicle will handle and react differently both on and off road. You must drive it safely! Extreme care must be taken to prevent vehicle rollover or loss of control, which could result in serious injury or death. Avoid sudden sharp turns or abrupt maneuvers and always make sure all vehicle occupants have their seat belts fastened.
(more…)

• 0 Comments