- Locate rear bumper attachment point on driver side.
- Remove bumper fasteners.
- Install mounting bracket onto linkage as shown. Torque to 33 ft-lbs / 44 Nm.
NOTE: 2500, 3500 HD trucks do not use spacer ( 5 ). Use fastener ( 2 ) on HD trucks.
- Slide upper mount over factory studs, install fasteners and torque to 70 ft-lbs / 95 Nm.
- Install step pad assembly onto linkage assembly with two socket cap screws.
- Adjust step pad position side to side. Allow for foot access. Torque allen head bolts to 10 ft-lbs / 13.5 Nm.
(more…)

• 0 Comments

Thank you for purchasing the Self Leveling Kit for your Kelderman Air Ride System. The kit consists of an air compressor, air tank and height control valve and linkage The kit also includes the needed mounting brackets and hardware that will give the air ride automatic ride adjustment.
Installing the Self Leveling Kit
Step 1. Height Control Valve: This mounts to the top air ride frame (unless ‘94-’02 Dodge). To locate, hold the height control valve on top of the air ride top frame plate and set it so the front hole of the height control arm is equal to the end of the swing arm.
(more…)

• 0 Comments

The engine won’t start or is difficult to start due to a carbon-fouled spark plug. The problem occurs on ACS (Automatic Choke System) GCV160 engines on certain Troy-Bilt lawn mower models. ARCS (Auto Return Choke System) engines are not affected.
The fouling is most likely to occur when the engine is started and the choke butterfly takes too long to open, or the shaft binds in the carburetor, resulting in a fouled spark plug.
(more…)

• 0 Comments

Front Door Installation for Magnum, Charger, 300C
1. Using a pick tool pry open the screw covers behind the interior door release lever and below the
arm rest and remove the screws. Fig. 1
2. Remove the four screws securing the door panel along the bottom. Fig. 1
3. Using the end of a Phillips screwdriver gently depress the center pin of the three plastic retainers
securing the door panel. The center pin of the plastic retainer should depress approximately 1/8”
and allow the retainer to be removed from the door panel. The two uppermost retainers do not
need to be removed in order to remove the door panel. Fig. 2
(more…)

• 0 Comments

1. Before servicing the vehicle, refer to the Precautions section. 2. Remove or disconnect the following: • Negative battery cable • Transfer case, if equipped • Transmission 1 • Pressure plate. Loosen the bolts evenly in /2 turn steps. • Clutch disc To install: 1. Install or connect the following: • Clutch disc and pressure plate. Tighten the pressure plate bolts evenly in /2 turns to 23 ft. lbs. (31 Nm) for 2.4L and 2.5L engines; 37 ft. lbs. (50 Nm) for 4.0L engines. • Transmission • Transfer case, if equipped • Negative battery cable
(more…)

• 0 Comments

Wiper and Washer System — Front Item Part Number Description 1 W707014-S441 Wiper pivot arm nut 2 17526 Wiper pivot arm (LH and RH) 3 N807391 Wiper pivot arm linkage bolt (3 required) 4 17508A Wiper pivot arm linkage assembly (includes wiper motor) 5 — Wiper motor crank bolt 6 — Wiper motor attachment bolt (3 required) (Continued) 7 17508B Wiper motor 1 W708312 Wiper pivot arm nut 2 17526 Wiper pivot arm (more…)

• 0 Comments

Attaching motor to linkage assembly The motors must be attached to the linkage assemblies before continuing the installation process.
PARTS LIST AND HARDWARE IDENTIFICATION (A) 19-03225-11 End cap left (x1) D (B) 19-03225-12 End cap right (x1) (C) 19-02663-90 T-nut insert (x2) (D) 19-03236-90 Socket cap screw (x2) (E) 19-03237-90 Nut plate (x2) Running board assembly GRIND 1/4″ EXCURSION ONLY 3 x2 (more…)

• 0 Comments

The ES177C2(-S) Series Floating Actuators are direct-mount, spring return electric actuators that operate on AC/DC 24 V power. These bidirectional actuators do not require a damper linkage and are easily installed on dampers with 1/2 to 3/4 in. or 12 to 19 mm round shafts, or 3/8 and 1/2 in. or 10, 12, and 14 mm square shafts using the standard shaft clamp included with the actuator. An optional M9220-600 Jackshaft Coupler Kit is available for 3/4 to 1-1/16 in. or 19 to 27 mm round shafts, or 5/8 and 3/4 in. or 16, 18, and 19 mm square shafts.
(more…)

• 0 Comments

Front Door Installation for Magnum, Charger, 300C
1. Using a pick tool pry open the screw covers behind the interior door release lever and below the arm rest and remove the screws.
2. Remove the four screws securing the door panel along the bottom.
3. Using the end of a Phillips screwdriver gently depress the center pin of the three plastic retainers securing the door panel. The center pin of the plastic retainer should depress approximately 1/8” and allow the retainer to be removed from the door panel. The two uppermost retainers do not need to be removed in order to remove the door panel.
(more…)

• 0 Comments

Attaching motor to linkage assembly
The motors need to be installed before continuing with the rest of the Power.
Step install.
CAUTION: HANDLE WITH CARE.
To insure our customers receive all components with full integrity, we pack the motors seperate from their linkage assemblies. This requires that the installer position and fasten the motor before continuing with the install. Please follow the instructions below and handle the assembly carefully.
CAUTION: Dropping the assembly or any excessive impact MAY cause damage to the motor.
(more…)

• 0 Comments