Models: 6405/4410 & 6405/4410TK GM/Chevrolet 2007 – current (new body style) full size trucks and SUVs with manual power mirrors.
THIS SET IS DESIGNED FOR TRUCK WITH STOCK MANUAL MIRRORS. IF YOU CURRENTLY HAVE POWER MIRRORS, THE WRONG SET HAS BEEN ORDERED.
(more…)

• 0 Comments

This coil spring lift kit should only be installed on vehicles in good working condition. Before installation, the vehicle should be thoroughly inspected for evidence of corrosion or deformation. This coil lift kit should not be installed on any vehicle that is suspected to have been in a collision or misused. Failure to observe this warning may result in serious personal injury and/or severe damage to your vehicle.
(more…)

• 0 Comments

The installation of the StopTech 350Z Rear Brake Upgrade requires extensive trimming of the splash guard/dust shield and filing or grinding of one of the caliper mounting lugs. The use of a powered cutoff wheel is likely necessary to trim the splash guard.
Only a qualified and experienced technician should perform this part of the installation as the use of power tools can cause serious injury if proper safety precautions are not taken. If you are unsure in your ability to make these modifications, please seek the help of a qualified technician.
Hand Brake Limitation
The emergency/parking brake can not be used as an active braking device such as hand brake turns or drifting competition. The aluminum hat portion that acts as the brake drum will hold the car in any parking situation and work for a single emergency stop, but will not stand up to use as a supplement to regular braking.
STEP 1 – Raise Vehicle and remove wheels. Apply Parking brake and block front wheels. Break loose the lug nuts on both rear wheels before jacking up the car. Refer to the Owners Manual for correct location for jacking up the vehicle. Jack up the vehicle and secure on a pair of jack stands. Never leave any vehicle supported with only a jack – always use jack-stands. After securing the vehicle at a convenient height, remove the rear wheels.
Note: If you remove the bottom lug nut last while holding the bottom of the tire, it will lessen the chances of the wheel tilting on it’s own and make removal easier. Right rear corner with wheel removed.
STEP 2 – Disconnect Stock Brake Line
WARNING – Brake fluid will damage most painted surfaces. Immediately clean spilled brake fluid from any painted surfaces.
NOTE – Be sure the cap is securely installed on the master cylinder. If the cap is loose or removed, it is likely more fluid will drip.
Place a drip tray or several rags directly below the inboard brake line connection. If the area around the brake line connection to the chassis and strut is dirty, clean with brake cleaner or appropriate cleaning agent.

Source

• 0 Comments

Application for 2005 – 2011 Ford Mustan. Note: Use of these components will require 18” Wheels minimum. It is the responsibility of the customer to verify that their wheels will fit. Note: The factory supplied Temporary Spare Tire will no longer fit the front of the vehicle with this kit. If you have a flat front tire, we recommend placing the mini spare on the back and transferring an 18 inch wheel to the front.
(more…)

• 0 Comments

This kit was designed for use with TM Kit# F4531. Use of this kit with other suspension kits and shocks, including coilovers, has not been verified. Proceed with caution. Interferences may exist. This kit should only be installed on a vehicle that is in good working condition. Before you install the kit, thoroughly inspect the vehicle for corrosion or deformation of the sheet metal. If the vehicle is suspected to have been in a collision or misused, do not install this kit. Off-road use of your vehicle with this kit installed may increase the stress applied to the factory components. Failure to observe this warning may result in serious personal injury and/or severe damage to your vehicle.
(more…)

• 0 Comments

Prepare to Install Kit
1. Front axle
a. If equipped, remove two caps (4) from front wheels (5).
b. Loosen eight lug nuts (6) each from two front wheels (5).
c. Using a hydraulic jack, slowly lift front axle (7) so that two front tires (8) are three to five inches off of ground. Position jack stands under frame (9). Lower frame onto jack stands. DO NOT remove hydraulic jack and maintain some hydraulic jack pressure on axle.
d. Remove eight lug nuts (6) each and two front wheels (5) from axle (7)
(more…)

• 0 Comments

REMOVAL OF EXISTING MIRRORS
1. Have both windows in the down position. To remove the trim panel on both doors, first remove the panel around the door handle, using 10 mm socket remove the screw holding the door handle. Next remove the four screws that hold the door trim panels in place (See diagram A on page 5). Remove the door trim panel by lifting up and then out.
2. Unplug the electric cord that comes from the mirrors located at the rear of each mirror at the mirror mount area.
3. Support the stock mirror while removing the 3 mirror mount lug nuts using a 10 mm socket. Save the stock nuts for later in the install.
4. Remove the stock mirror (save the stock gaskets as they will be re-used).
(more…)

• 0 Comments

FRONT STRUT REMOVAL
1. Loosen the front wheel lugnuts.
2. Raise the vehicle and support it on jack stands.
3. Remove the front wheels.
4. Disconect the air line fitting and unplug the electrical connectors for the height sensor and solenoid.
5. Then vent the air from the bag.
6. Be sure to mark the position of the strut at the bottom where it bolts to the spindle.
7. Remove the nuts and bolts from the strut.
8. Be sure to disconnect the brake hose from the strut.
9. Now remove the upper three nuts where it attaches to the shock tower.
10. Now dismount the strut from the vehicle.
(more…)

• 0 Comments

INSTALLATION
Note: This kit is designed to be used on 74-78 Mustang II and 73-80 Pinto/Bobcat spindles. It will also fit most dropped spindles and tubular “A” arm combinations. Check the fit before painting or plating any parts.
Painted, plated or modified pants are not accepted for return.
1. Starting with a clean spindle, mount the appropriate bracket {there is a right and left hand bracket) to the spindle using the bolts supplied. Note: brackets stamped R are right-passenger side and L are left-drivers side.
(more…)

• 0 Comments