The Moroso Dry Sump Oil Pump is designed to fit either 90° V-6, small or big block Chevrolets, and the only difference is the mounting holes. You can see that there are two sets of slotted holes on the mounting bracket, which attaches the pump to the engine block.
(more…)

• 0 Comments

- Locate rear bumper attachment point on driver side.
- Remove bumper fasteners.
- Install mounting bracket onto linkage as shown. Torque to 33 ft-lbs / 44 Nm.
NOTE: 2500, 3500 HD trucks do not use spacer ( 5 ). Use fastener ( 2 ) on HD trucks.
- Slide upper mount over factory studs, install fasteners and torque to 70 ft-lbs / 95 Nm.
- Install step pad assembly onto linkage assembly with two socket cap screws.
- Adjust step pad position side to side. Allow for foot access. Torque allen head bolts to 10 ft-lbs / 13.5 Nm.
(more…)

• 0 Comments

Installation Stainless Steel Oval on Dodge RAM HD Crew Cab:
1. Read instructions completely and check to make sure that all required parts (listed on service parts list) are on hand before starting the installation.
2. Oval step assemblies and brackets (item #1 & 2) are pre-assembled.
2.1. The front and rear mounting brackets on these assemblies are rotated for shipping purposes. These brackets must be rotated to the vertical position and the ‘/2″ bolts. Torque to 65 lb ft.
(more…)

• 0 Comments

Thank you for purchasing the Self Leveling Kit for your Kelderman Air Ride System. The kit consists of an air compressor, air tank and height control valve and linkage The kit also includes the needed mounting brackets and hardware that will give the air ride automatic ride adjustment.
Installing the Self Leveling Kit
Step 1. Height Control Valve: This mounts to the top air ride frame (unless ‘94-’02 Dodge). To locate, hold the height control valve on top of the air ride top frame plate and set it so the front hole of the height control arm is equal to the end of the swing arm.
(more…)

• 0 Comments

PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
2. Starting at the Passenger/Right side-front of the vehicle, remove the front factory body bolt & washer.(not re-used) (Fig 1), From the list above select the Passenger/Right side front mounting bracket and the spacer Block secure to vehicle with (1) 12mm x 150mm Hex Bolt, (1) 12mm Flat Washer, (1) 12mm Lock Washers (Fig 1A). Snug but do not tighten hardware at this time.
3. Next, select the T Bolt from the list of parts above, and place the T Bolt into the opening on the Passenger/Right side bottom front frame rail (Fig 2 shows T Bolt placed into frame rail.
(more…)

• 0 Comments

This document describes the steps for upgrading a Need for Speed™ Underground Deluxe Motion Cabinet to Need for Speed™ Carbon. The Upgrade Kit includes a new computer, Software, Game Dongle, Artwork, and an external mounting bracket for the Nytric USB I/O PCB. Need for Speed™ Carbon software requires a new computer. You will need to remove the Digital- Analog Converter (DAC) card and Nytric USBI/O PCB from your existing computer.
(more…)

• 0 Comments

Preparing Vehicle
Make sure vehicle is parked on level surface.
Set parking brake.
If engine has run in the past two hours, let it cool down.
Disconnect negative battery terminal.
Raise the front of the vehicle with a jack. Refer to your owner’s manual for proper jack and jack stand placement to properly support vehicle. Support your vehicle using properly rated jack stands before wheel removal or while working under the vehicle.
NEVER WORK UNDER A VEHICLE WITHOUT USING JACK STANDS.
Do not discard stock components after removal of the factory system.
(more…)

• 0 Comments

I. Preparing the Vehicle
1. Elevate the vehicle and secure the frame with jack stands.
2. Remove the front wheels.
II. Strut Removal
1. Remove the three nuts securing the upper strut mounting bracket and discard.
NOTE: These are located inside the engine compartment above the strut pocket.
3. Remove the upper clevis retaining bolt and save for reinstallation.
4. Lift the lower end of the strut out of the clevis and remove the strut from the vehicle.
(more…)

• 0 Comments

Installation: 2002 Taurus
This siren will be mounted onto the vehicle horn’s mounting plate near the drivers side front tire. The vehicle horn’s mounting holes will be used to mount the SA314 siren speaker.
WARNING! Loud siren noise can cause hearing loss. Minimize exposure. Close windows when using.
1. Since the siren will be mounted upside down, its drain hole is now on top. This requires another drain hole to be drilled into the siren before mounting (See “Drilling the drain hole”).
2. Mount siren onto the bracket using the supplied mounting hardware. Install a spacer nut onto each of the bracket’s Pem Studs (Fig. 2).
3. Remove the large (full vehicle width) plastic splash guard mounted to the front, underside of the vehicle (Fig. 1). This allows access to the vehicle horn.
(more…)

• 0 Comments

Instructions for K&N Filters Kit on Celica GT4
1. Unclip and remove the electrical harness plug from the AFM (Air flow meter)
2. Unclip and remove the intake hose from the AFM.
3. Unclip and remove the air box lid assembly.
4. Unscrew and remove the air box base from the inner wing.
5. Remove the AFM from the air box lid by removing the 4 bolts from inside the lid and the single bolt securing the AFM bracket to the outside of the lid.
(more…)

• 0 Comments