Installation Instructions. Read Me! Rv. 01/04
1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove throttle body air intake system.
3. Remove (3) nuts & studs from the throttle body & manifold. (Ref. “C”)
4. Remove support bracket from engine block to throttle body. (Ref. “D”)
* Please Note: When removing support bracket bolt at engine block, loosen bolt enough to remove bracket. DO NOT REMOVE BOLT.
(more…)

• 0 Comments

TO START the Installation:
1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable.
2. Remove the four 13mm nuts that secure the strut toner brace to vehicle, then remove brace from vehicle.
3. Squeeze the two locking tabs together, then remove the mass air electrical connection as shown.
4. Loosen the hose clamp at the intake plenum and release the two clips that secure the air box lid to vehicle, then remove the upper air box and intake tube as shown.
(more…)

• 0 Comments

1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable.
2. Disconnect the mass air sensor electrical connection.
3. Remove oil cap, then pull up on engine cover to release from its retainers.
4. Disconnect the crank case vent hose from the intake plenum.
5. Loosen the two hose clamps on the intake plenum, then remove the intake plenum from the vehicle as shown.
(more…)

• 0 Comments

The K&N intake tube installation:
1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable.
2. Disconnect the mass air sensor electrical connection.
3. Loosen hose clamp at the mass air, then remove the three 10mm bolts that secure air box to vehicle.
4. Remove air box from vehicle as shown.
(more…)

• 0 Comments

The installation instructions step:
1. Disconnect the negative battery cable! Loosen two hose clamps and remove the air intake tube. Separate the intake tube from the plastic clamp on the upper radiator hose. (If equipped).
2. Using a 10mm socket, remove the three nuts that hold the throttle body to the intake manifold.
3. Using a 4mm socket, remove the three studs that go thru the throttle body into the intake manifold.
(more…)

• 0 Comments

TO START:
1. Turn off the ignition and disconnect the negative battery cable.
2. Disconnect the mass air sensor electrical connection and unhook the mass air sensor wiring from the engine cover.
3. Remove the two screws shown that secure the fresh air tube to the fresh air duct.
4. Pull up firmly on the air filter housing/engine cover assembly to release it from the mounting grommets.
NOTE: The air filter housing/engine cover assembly is still attached to the intake inlet tube.
5. Using pliers, release the spring clamp that secures the intake to the intake inlet. Then unhook the intake tube from the inlet.
(more…)

• 0 Comments

When installing this exhaust system make sure to use proper safety precautions. Use jack stands when working under the vehicle, set parking brake, block tires and use safety glasses and gloves. Allow exhaust to cool before attempting installation. Severe injury or burns could occur if safety measures are not taken.
(more…)

• 0 Comments

TO START:
1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable.
2. Disconnect the mass air sensor electrical connection.
3. Loosen the hose clamp on the intake tube at the throttle body.
4. Loosen and remove the bolt that secures the air cleaner assembly to the inner fender.
5. Detach the crank case vent hose from the intake tube.
(more…)

• 0 Comments

Please follow these installation instructions carefully. The K&N Drycharger included in this kit must be installed on the K&N air filter when used with a K&N Typhoon Cold Air Intake System. The K&N Typhoon Intake System is a performance product that can be used safely during mild weather conditions. During hard and inclement weather conditions, you must convert your Cold Air Intake System into a short ram configuration, or return your vehicle to the stock OEM airbox and intake tract configuration. Failure to follow these instructions can void your warranty.
(more…)

• 0 Comments

Installation Step:
1. Disconnect the negative battery cable! Push the green tab on the crankcase breather tube, and disconnect it from the air intake tube. Loosen one hose clamp on each end of the air intake tube and remove it from the vehicle.
2. Remove the four bolts that hold the throttlebody to the intake manifold.
3. Install the ECONOAID Plate against the manifold with the logo facing the throttlebody. Next install the supplied gasket between the ECONOAID Plate and the throttlebody.
(more…)

• 0 Comments