While it may be possible to install this kit without removing the bed, it is recommended that you do so, as it is much easier. Support the front and rear of the chassis on jack stands. Be safe! Avoid pulling and pushing on the vehicle while it is off the ground. Remove the rear axle assembly, stock springs, shocks and brackets.
(more…)

• 0 Comments

Prepping The Block
Disconnect battery; remove all existing accessory drive brackets and components from motor.
Remove water pump, scrape away any existing gasket material with a gasket scraper and dress surface with a Scotch Brite® pad.
Clean and prep threads on engine block at water pump and driver side bosses by crank (for power steering kits), use a 3/8-16 thread chaser if necessary. Thread chasers are available at your local auto parts store or tool dealer and are different from a thread cutting tool.
(more…)

• 0 Comments

Some specific model year 2009 – 2010 Altima and Maxima vehicles may have been built with front strut mounting insulators that were not manufactured to specification. The strut mounting insulators on these specific vehicles may crack. To remedy this potential condition Nissan is conducting this voluntary safety recall campaign to replace the strut mounting insulators with new ones at no charge for parts or labor.
(more…)

• 0 Comments

Please remove the Std intercooler ,top Std intercooler pipe , front bar ,front reinforcement prior install the top Hybrid intercooler pipe. (make sure all super clamps are loose for further adjustments.) Hybrid Nissan R33 GTS intercooler kit Installation instruction Note Picture may be different than the actual product! It is a reference guide only! Page 2 Parts list Piping, silicon hose and super clamp kit 3 custom pips set Description Qty 2.5” super clamps 6 3”super clamps 2 2.5”-3” silicon reducer 2 2.5” silicon hose 2 Spacers 2 Screws 6 Nuts 2 Long lower bracket 2 Short top bracket
(more…)

• 0 Comments

1994-95 models 2500 and 3500 with 5.9 diesel or 8.0 ltr. V-10, The vehicle manufacturer has a safety recall #835, which reinforces the coil towers. The part # for this upgrade is #CBBR8352. Check with your local dealer in regards to this upgrade prior to installing this suspension system.
-This supplement will be used when installing Platinum Series shocks and coils.
1. Platinum Series Coil Over Installation Guide.
(more…)

• 0 Comments

Removal, overhaul and installation procedures are covered in this article. If component removal and installation is primarily an unbolt and bolt-on procedure, only a torque specification may be furnished.
NOTE: Mirage 1.6L uses Distributorless Ignition System (DIS). For exploded view of distributor on all other models,
FUEL SYSTEM
WARNING: Always relieve fuel pressure before disconnecting any fuel injection-related component. DO NOT allow fuel to contact engine or electrical components.
(more…)

• 0 Comments

1: Here is the Subaru WRX Lower Mesh Grille Kit Part# SUB-1712 available in silver or black finishes.
2: Here is our project WRX in need of a GrillCraft Mesh Grille for added protection and styling.
3: Start by removing the upper grille push down on retaining clips as shown.
4: There are two lower retaining clips down below a long screwdriver will release them.
5: Now the grille can be removed.
6: Remove bumper cover push clips.
7: Remove filler panel there is a push clip on the back side.
8: Remove headlamp in order to gain access to the clip behind it.
(more…)

• 0 Comments

INSTALLATION Roof Rack on 2008 CR-V
NOTE: Be careful not to damage the roof and other finished surfaces of the body when installing the roof rack.
1. Using a flat-tip screwdriver wrapped with a shop towel, remove the four roof trim covers (four retaining tabs for each cover).
2. Clean the paint off of the mounting studs. Thread on a special nut until you feel resistance, then turn it an additional 90°. Remove the nut, and blow the nut and stud clean with compressed air. Repeat this process until the nut threads all the way on.
3. Repeat step 2 for all of the remaining studs.
(more…)

• 0 Comments

This B&M Short Throw Shifter has been designed to work on most 1996-2000 Audi A4, 2000 Audi S4, 2000 Audi A6, and 1996-2000 Volkswagen Passat models. It has been engineered to greatly reduce shift throw and improve shifter feel. Check the parts and tools lists at the beginning of these instructions for the supplied parts and the tools required to install your B&M Short Throw Shifter. Installation of the B&M Short Throw Shifter can be accomplished by anyone with minimal mechanical experience.
(more…)

• 0 Comments

Removal of air intake plenum:
First of all, the task at hand is really easier than it appears. The only thing is… it takes time. If you know nothing about cars or what things are under the hood, I suggest you take a look at figure 18 and see if this is comprehendible to you. If it is and you have the tools and feel comfortable, please proceed. If not, I suggest you find a qualified mechanic instead of doing it yourself. The plenum itself is actually very easy to unbolt, only 13 bolts & nuts hold it in place. (fig. 19) What makes it complicated is all the other stuff you have to unbolt and move out of the way so your plenum is free to completely flip up and give you full access to the sparkplugs.
(more…)

• 0 Comments