Front Door Installation for Magnum, Charger, 300C
1. Using a pick tool pry open the screw covers behind the interior door release lever and below the
arm rest and remove the screws. Fig. 1
2. Remove the four screws securing the door panel along the bottom. Fig. 1
3. Using the end of a Phillips screwdriver gently depress the center pin of the three plastic retainers
securing the door panel. The center pin of the plastic retainer should depress approximately 1/8”
and allow the retainer to be removed from the door panel. The two uppermost retainers do not
need to be removed in order to remove the door panel. Fig. 2
(more…)

• 0 Comments

Subwoofer Installation 1. Find the fuse block under the hood and open the fuse box cover.
2. Using a 13mm socket and ratchet loosen and remove the fuse box power supply nut.
3. Connect the ring terminal of the power harness to the fuse box power lug and retighten the nut.
4. Route the wire toward the rubber grommet in the fire wall where the hood release cable passes through securing with wire ties where needed.
(more…)

• 0 Comments

This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur.
Removal NOTE: Front lock carrier (radiator support) must be moved forward to remove timing belt. 1. Raise and support vehicle. Remove front, lower engine cover. Lower vehicle. Separate release lever from hood lock. Remove front bumper cover. See Fig. 1 . Remove bumper carrier from impact damper. 2. Unbolt air duct between lock carrier and air cleaner on lock carrier. Remove support bolt on passenger side of lock carrier and insert one Lock Carrier Guide (3369) into hole. See Fig. 2 . 3. Remove lock carrier front support bolts. Remove lock carrier-to-side panel bolts. Insert Lock Carrier Guide (3369) into hole on driver’s side of vehicle. Slide lock carrier forward on lock carrier guides. 4. On (more…)

• 0 Comments

Press the CLOCk button to set hours then use the buttons to adjust 02 01 or Press the CLOCk button again to set minutes then use the or buttons to adjust Press the CLOCk button again to exit clock set mode INTERIOR TRUNk LID RELEASE REMOTE kEyLESS ENTRy SySTEM if so equipped LOCk DOORS Press the LOCk button to lock all doors UNLOCk DOORS Press the UNLOCk button once to unlock the driver s door only Press the button again within 5 seconds to unlock all doors RELEASING TRUNk LID This easy to use Quick Reference Guide is intended to help you more fully appreciate some of the unique features and functions of your new vehicle However it is not intended to replace your Owner s Manual
(more…)

• 0 Comments

Front Door Installation for Magnum, Charger, 300C
1. Using a pick tool pry open the screw covers behind the interior door release lever and below the arm rest and remove the screws.
2. Remove the four screws securing the door panel along the bottom.
3. Using the end of a Phillips screwdriver gently depress the center pin of the three plastic retainers securing the door panel. The center pin of the plastic retainer should depress approximately 1/8” and allow the retainer to be removed from the door panel. The two uppermost retainers do not need to be removed in order to remove the door panel.
(more…)

• 0 Comments

Neon Front Door Instructions:
1. Using a pick tool pry open the screw cover behind the interior door release lever and remove the screw.
2. Remove the screws in the armrest pocket and at the top of the door near the front.
3. For models with manual windows use a window crank removal tool to disengage the pin securing the window
crank and pull the window crank from the door. The triangle shaped piece that houses the side mirror
adjustment control lever will need to be pulled away from the door. Using a panel removal tool gently pry
the bottom of the plastic away from the door to release the fasteners and let it hang by the mirror control cables.
(more…)

• 0 Comments