Preparation
1. Ensure all lamps and accessories are OFF.
2. Ensure the ignition switch is in the OFF position.
3. Loosen the negative battery cable bolt.
Remove negative battery cable from terminal and position away from battery.
4. Wait one (1) minute prior to working on the vehicle to assure SIR roof rail airbag system has been disabled for your safety.
(more…)

• 0 Comments

Preparation
1. Ensure all lamps and accessories are OFF.
2. Ensure the ignition switch is in the OFF position.
3. Loosen the negative battery cable bolt.
Remove negative battery cable from terminal and position away from battery.
4. Wait one (1) minute prior to working on the vehicle to assure SIR roof rail airbag system has been disabled for your safety. Install Camera into Endgate
(more…)

• 0 Comments

Front Door Installation for Magnum, Charger, 300C
1. Using a pick tool pry open the screw covers behind the interior door release lever and below the arm rest and remove the screws.
2. Remove the four screws securing the door panel along the bottom.
3. Using the end of a Phillips screwdriver gently depress the center pin of the three plastic retainers securing the door panel. The center pin of the plastic retainer should depress approximately 1/8” and allow the retainer to be removed from the door panel. The two uppermost retainers do not need to be removed in order to remove the door panel.
(more…)

• 0 Comments

Installation Procedure:
1. To begin installation, block rear wheels and apply parking brake so that the vehicle is stable and cannot roll forward or back. Lift front of the vehicle on appropriate lift points, such as the frame, and support the frame with jack stands on both passenger and driver sides. Remove front wheels.
2. Position a floor jack under the front axle and raise jack until it makes contact with the front axle. (See Figure 1)
3. On the drives side, place an index mark on the stock coil spring and another index mark directly across from the first mark on the lower coil spring perch. This will allow you to reinstall the stock coil spring in its original position. Repeat step 3 on passenger side.
(more…)

• 0 Comments

PROCEDURES:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. DRILLING MAY BE REQUIRED.
2. From underside the driver side front of the vehicle, remove the factory body mount bolt. Remove but do not discard the rubber bushing. Install (1) 12-1.75mm x 120mm Hex Bolt with (1) 12mm ID x 30.1mm OD x 3.1mm Flat Washer and (1) 12mm Lock Washer through the Driver Side Front Mounting Bracket. Position (1) Spacer Plate between the Mounting Bracket and the factory rubber bushing, (Figure 4). Slide the complete assembly up into position under the cab mounting bracket and thread the 12mm Hex Bolt into the factory mounting hole. Snug but do not tighten at this time.
(more…)

• 0 Comments

Notes:
• Tool kit contains more parts than are required for Chrysler RWD installation – follow instructions.
• This tool kit can also be used to install 56361-01K case repair sleeve in A4LD, 4R44/55E, 5R55E, AOD & E and 4R70W

Installation Instructions
1. Remove valve body and manual shaft seal.
2. Clean seal bore and pan/valve body surface of case. Run a file across case pan gasket surface to make sure there are no nicks or burrs where the reamer guide plate attaches to case.
(more…)

• 0 Comments

This kit allows the owner of any BMW to attach a front license plate to their BMW without the need to drill holes. BMW has always attached the front license plate by drilling the front bumper and permanently mounting the plastic license plate bracket to the front bumper with screws. The ‘NO HOLES’ kit mounts the front license plate utilizing the front tow hook attachment point. The kit comes complete with all mounting hardware, including the screws to affix the license plate to the bracket. The bracket allows for the mounting of normal size US License plates, Rallye Plates and European style plates.
(more…)

• 0 Comments