This coil spring lift kit should only be installed on vehicles in good working condition. Before installation, the vehicle should be thoroughly inspected for evidence of corrosion or deformation. This coil lift kit should not be installed on any vehicle that is suspected to have been in a collision or misused. Failure to observe this warning may result in serious personal injury and/or severe damage to your vehicle.
(more…)

• 0 Comments

Disassembly
1. WARNING: To reduce the risk of serious personal injury, read and follow all warnings, notes and instructions in the steering column removal and installation procedure.
Remove the steering column. For additional information, refer to Steering Column in this section.
2. Remove the clockspring. For additional information, refer to Section 501-20B.
3. Remove the multifunction switch.
4. Unclip the steering column opening gearshift lever seal from the steering column.
(more…)

• 0 Comments

Do not smoke, carry lighted tobacco or have an open flame of any type when working on or near any fuel-related component. Highly flammable mixtures are always present and may be ignited. Failure to follow these instructions may result in serious personal injury.
1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02.
2. Release the fuel system pressure. For additional information, refer to Section 310-00.
3. Disconnect the battery ground cable. For additional information, refer to Section 414-01.
4. Recover the A/C system. For additional information, refer to Section 412-00.
5. NOTE: Use a steering wheel holding device (such as Hunter® 28-75-1 or equivalent). Using a suitable holding device, hold the steering (more…)

• 0 Comments

This kit was designed for use with TM Kit# F4531. Use of this kit with other suspension kits and shocks, including coilovers, has not been verified. Proceed with caution. Interferences may exist. This kit should only be installed on a vehicle that is in good working condition. Before you install the kit, thoroughly inspect the vehicle for corrosion or deformation of the sheet metal. If the vehicle is suspected to have been in a collision or misused, do not install this kit. Off-road use of your vehicle with this kit installed may increase the stress applied to the factory components. Failure to observe this warning may result in serious personal injury and/or severe damage to your vehicle.
(more…)

• 0 Comments

This manual includes information for all options available on this model Therefore you may find some information that does not apply to your vehicle All information specifications and illustrations in this manual are those in effect at the time of printing NISSAN reserves the right to change specifications or design without notice and without obligation IMPORTANT INFORMATION ABOUT THIS MANUAL You will see various symbols in this manual They are used in the following ways WARNING This is used to indicate the presence of a hazard that could cause death or serious personal injury To avoid or reduce the risk the procedures must be followed precisely The inside pages of this manual contain a minimum of 50 recycled fibers including 10 post consumer fibers CALIFORNIA PROPOSITION 65 WARNING WARNING Engine Exhaust some of its constituents and certain vehicle components contain or emit chemicals known to State of California to cause cancer and birth defects or other reproductive harm 2000
(more…)

• 0 Comments

Proper installation of this kit requires knowledge of the factory recommended procedures for removal and installation of original equipment components. We recommend that the factory shop manual and any special tools needed to service your vehicle be on hand during the installation. Installation of this kit without proper knowledge of the factory recommended procedures may affect the performance of these components and the safety of the vehicle. We strongly recommend that a certified mechanic familiar with the installation of similar components install this kit
(more…)

• 0 Comments

Prepare to Install Kit
1. Front axle
a. If equipped, remove two caps (4) from front wheels (5).
b. Loosen eight lug nuts (6) each from two front wheels (5).
c. Using a hydraulic jack, slowly lift front axle (7) so that two front tires (8) are three to five inches off of ground. Position jack stands under frame (9). Lower frame onto jack stands. DO NOT remove hydraulic jack and maintain some hydraulic jack pressure on axle.
d. Remove eight lug nuts (6) each and two front wheels (5) from axle (7)
(more…)

• 0 Comments

Installation of a Performance Automotive group body lift will change the center of gravity and the handling characteristics of the vehicle. Because of the higher center of gravity and larger tires, the vehicle will handle and react differently both on and off road. You must drive it safely! Extreme care must be taken to prevent vehicle rollover or loss of control, which could result in serious injury or death. Avoid sudden sharp turns or abrupt maneuvers and always make sure all vehicle occupants have their seat belts fastened.
(more…)

• 0 Comments