STEP 1 : VEHICLE COMPATIBILITY
Downloadable Firmware for Platform XK01: GMDL5X, GMDL6X, GMDL7X
Default firmware on the XK1 platform is GMDL6X. If the vehicle you are working in is not in the GMDL6X list, you will need to reprogram the XK1 platform with the desired firmware.
(more…)

• 0 Comments

Installation of this baseplate requires drilling 17/32” holes in the vehicle’s frame.
1. Read the General Instruction Sheet included with this baseplate.
2. The baseplate bolts to the bottom of the frame behind the bumper using six bolts supplied with the baseplate. Use of Loctite to secure the bolts is highly recommended. The vibrations and stresses of towing can cause bolts to loosen even with lock washers in the assembly.
(more…)

• 0 Comments

Thank you for purchasing the Self Leveling Kit for your Kelderman Air Ride System. The kit consists of an air compressor, air tank and height control valve and linkage The kit also includes the needed mounting brackets and hardware that will give the air ride automatic ride adjustment.
Installing the Self Leveling Kit
Step 1. Height Control Valve: This mounts to the top air ride frame (unless ‘94-’02 Dodge). To locate, hold the height control valve on top of the air ride top frame plate and set it so the front hole of the height control arm is equal to the end of the swing arm.
(more…)

• 0 Comments

This B&M Precision Sport Shifter has been designed to work on most models listed above equipped with a manual transmission. It has been engineered to greatly reduce shift throw and improve shifter feel. Check the parts list and tool lists at the beginning of these instructions for the supplied parts and the tools required to install your B&M Precision Sport Shifter. Installation of the B&M Precision Sport Shifter can be accomplished by anyone with minimal mechanical experience.
(more…)

• 0 Comments

Prepare for the installation.
• If possible, install the SWI-X while you are installing the new head unit. Keep in mind you may need to plug in the factory stereo to locate certain wires; therefore do not complete the head unit installation until the SWI-X is working properly.
• Plan a general installation location for both the SWI-X LED and the control body. Keep in mind that the supplied wire harness is two feet long, and the IR harness is four feet long.
• Use a multimeter or approved measuring device for checking vehicle circuits.
(more…)

• 0 Comments

Make sure you maintain the vehicle in a clean pristine condition, and trim components are undamaged and placed back into position. Always protect the painted and interior surfaces, on all vehicles during the installation. Have a clean terry cloth and cleaning alcohol with you to clean off any fingerprints on the interior of the vehicles. Note: The 2008 TT is currently the only vehicle that can be ordered with CD Changer prep or CD Changer. The 2008 R8 must have a CD Changer to accommodate this installation.
(more…)

• 0 Comments

This mount will provide a great reduction in transmission movement making shifting much more secure. With less transmission movement you’ll have less drivetrain slop as well, resulting in more power transmitted to the wheels. Upgraded engine mounts are recommended to be used in conjunction. Below are our installation guidelines for this item. Please review them carefully before attempting to install this product.
(more…)

• 0 Comments

These arm will allow you to fine tune your alignment settings for minimizing tire wear, or for maximum track performance. These arms completely replace your existing upper control arms.
Step 1: Raise the entire front of the car and secure it with jack stands. Never work under a car supported only by a hydraulic floor jack. Check your owner’s manual for proper placement of floor jacks and jack stands. If you live in an area where rust is a concern liberal use of penetrating fluid will be necessary and may increase the installation difficult. If you have any concerns, please consult with a professional.
(more…)

• 0 Comments

The Adapter Plate kit will allow you to use Buick, Pontiac or Oldsmobile and Cadillac 200, 350 and 400 Turbo-Hydramatic Transmissions with a Chevrolet engine. No alterations are necessary and installation is easy and simple.
NOTE: On some Turbo 400 transmissions, the webbing located inside the bell housing may interfere with two of the adapter plate kit bolts. Webbing must be trimmed to clear these bolts.
(more…)

• 0 Comments

Installation Procedure:
1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove air cleaner
3. Using 1/2” socket, remove (3) 5/16’ bolts.
* Please Note: Some units have bolts that are drilled and tapped for air cleaner mounting studs.
4. It is not necessary to remove the fuel lines.
5. Remove fuel line bracket from transmission. (Located on drivers side of bell housing)
(more…)

• 0 Comments