Pre-fit before painting. Install new, unpainted parts according to these instructions. Then remove parts, paint them and re-install. Painted or Altered Parts are Non-Refundable. The exhaust system must be installed before the side skirts. Do not tighten exhaust clamps or bracket until installation is complete. The entire Sniper side skirt kit must be installed before exhaust tip installation. The surface temperature where the 2-sided tape is applied must be 75o or above. This temperature must be maintained for 24 hours without moving vehicle or the 2-sided tape will fail.
(more…)

• 0 Comments

The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
1. Allow the engine and all cooling system components to cool down.
2. Place a clean drain pan under the radiator drain plug, then remove the drain plug from the bottom of the radiator to drain the coolant. Remove the radiator cap to increase the flow.
(more…)

• 0 Comments

Exhaust System Removal:
For ease of installation and safety concerns, the use of a lift is recommended and be sure to wear safety glasses.
Prior to installation, be sure vehicle is parked on a level surface and the exhaust system is cool.
1) After your vehicle is properly secured and there is enough clearance to work from under the vehicle, the first step is to remove the oxygen sensor located between the catalytic converter and the center muffler – (See Fig. A). Use a 7/8-inch open-end wrench to remove the threaded sensor.
2) The next step is to determine where to cut the connecting pipe between the catalytic converter and center muffler. Using a tape measure, measure from the front edge of the catalytic converter flange (See Fig. C) back 20 INCHES for the STS or 18-1/2 INCHES for the DTS and mark the connecting pipe.
NOTE: Recheck your measurement
(more…)

• 0 Comments

Remove the front bumper cover
A. Begin by removing the dust covers that are located underneath the vehicle. Use the 10mm socket to remove the OEM bolts and then the 7mm Nut driver to removed all the OEM screws along the sub-front portion of the bumper.
B. Locate and remove all other fasteners that attach the OEM bumper cover to the vehicle. Once you’ve removed the fasteners, slowly remove the bumper cover. Note that some vehicles may have the foam bumper protector inside, where some may have the plastic protector. The Pro-gard Push Bumper was designed for the plastic protector.
(more…)

• 0 Comments

LIGHT BAR CUTTING INSTRUCTIONS
1. Two people will be needed to complete this task.
2. Place ONLY THE MOUNTING END CASTING into the rain-gutters of your vehicle.
3. Level each Mounting End Casting so that the top flat area is parallel to the horizon.
4. Take a tape measure and measure the distance between each open end of each Mounting End Casting .
5. Add 2 inches to that dimension.
6. Subtract that total from the total length of the bar, which is 56″.
7. Take the difference and divide it by two.
8. The amount divided by two is the amount you will cut off each end of your bar.
(more…)

• 0 Comments

Step 1-Unpack QuickLIFT kit and verify contents.
Remove all items from the packing tube. You should have the following before beginning:
* (2) Gas Charged Springs
* (4) 3/16″ multi-grip rivets – used on hood brackets
* (4) Self tapping high strength screws – used on fender brackets
* (4) Fender & Hood Steel brackets
* Printed Instructions
* Gas Spring locking clips (already installed on the gas spring ball ends – Remove before assembly – DO NOT LOSE, these are very small and disappear if dropped.)
(more…)

• 0 Comments

Procedures:
1. Make sure you park the vehicle on a level concrete or asphalt surface. Many times a vehicle is un level (side-to-side) from the factory, but usually not noticed until a lift kit has been installed which makes the difference more visible. Using a measuring tape, measure the front and rear (both sides) from the ground up to the center of the fender opening above the axle. Record below for future reference.
(more…)

• 0 Comments