This undercarriage fits all models listed but the cross member connection will vary. Refer to step “a” for the 1987–96 Dodge Dakota, 1997–03 Dodge Dakota Sport, 1997–03 Dodge Dakota SLT Extended Cab and 1998–03 Dodge Durango SLT models. Refer to step “b” for the 1997–04 Dodge Dakota and 1998–03 Dodge Durango.
Read the rest of this entry »

• 0 Comments

This undercarriage fits all models listed but the crossmember connection will vary. Refer to step “a” for the 1987-1996 Dodge Dakota, 1997-2003 Dodge Dakota Sport, 1997-2003 Dodge Dakota SLT Extended Cab and 1998-2003 Dodge Durango SLT models. Refer to step “b” for the 1997-2004 Dodge Dakota and 1998-2003 Dodge Durango
1. Disconnect the fog lamp harnesses if applicable, and then remove the bumper.
a. Remove the bumper mount plates from in between the frame rail and radiator. Discard the mount plate hardware.
b. Permanently remove the air dam from the truck frame crossmember. Remove the fasteners that are pressed into the bumper bracket on the frame rail. Secure the bracket and frame wall with vise grips and then use a hammer to punch out the fasteners.
Read the rest of this entry »

• 0 Comments

1. For the Dakota: Remove bumper, retaining all OEM fasteners for reinstallation.
Proceed to Step 2.
For the Durango: Prior to removing the bumper, cut and remove the center portion of the bumper and air dam as shown in the photo below. Retain the cut out section of the air dam to fabricate an air deflector in Step 8. Remove the remaining bumper assembly, retaining all OEM fasteners for reinstallation.
2. Clamp the driver-side mount plate to the outside of the driver-side vehicle frame. Make sure the mount alignment tab fits up against the back of the vehicle frame front plate, and the front and rear plate stiffeners are snug against the bottom of the frame. When positioned correctly, mount plate holes align near the center of the vehicle frame.
Read the rest of this entry »

• 0 Comments

The mounting procedure outlined below covers the 2000 – 2004 Dodge Dakota trucks. You will need to refer to the illustrations and familiarize yourself with each of the undercarriage components and their relative position to each other. Then proceed as follows:
1. Disconnect fog lamps from bumper if equipped on vehicle.
2. Cut rubber portion of air deflector attached to bumper and discard. Open vehicle hood and remove four vertical bumper bolts from existing Bumper Brackets (BB). Remove bolts from two outer bumper brackets if equipped on vehicle. Remove bumper.
3. Clamp existing Bumper Bracket (BB) to frame rail. Remove two existing Nuts (AA) from Bumper Bracket (BB). Use chisel and hammer between head of existing Bolts (CC) and Bumper Bracket (BB) to force them loose. Use caution to prevent damage to parts. Unclamp and remove Bumper Bracket (BB). Repeat process on opposite side of vehicle.
Read the rest of this entry »

• 0 Comments

This Borla Performance X-Pipe (Part number 60092) has been designed for the 2005-2008 Ford Mustang GT equipped with a 4.6L V8 engine and automatic or manual transmissions.
Original H-Pipe Removal
Note: With a used vehicle, we suggest a penetrating spray lubricant to be applied liberally to all exhaust fasteners and allowing a significant period of time for the chemical to lubricate the threads before attempting to disassemble.
1. Loosen the clamps shown in figure 1 located just behind the h-pipe.
2. Loosen the clamps shown in figure 2 located just in front of each muffler assembly.
3. Beginning with the left (driver) side, using a flat blade screwdriver, pull the clip as shown in figure 3 to disengage it from the pipe.
Read the rest of this entry »

• 1 Comment

Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing a Borla Performance Exhaust System on your vehicle will eliminate the restrictive design of the stock exhaust, allowing your engine to discharge exhaust gas easier. The result is more horsepower and torque, longer engine life, and a distinctive throaty growl- all this, with easy bolt-on installation. These installation instructions have been written to help you in the installation of your Borla Performance Exhaust System. Please read it completely before installing your system.
Read the rest of this entry »

• 0 Comments

When installing this exhaust system make sure to use proper safety precautions. Use jack stands when working under the vehicle, set parking brake, block tires and use safety glasses and gloves. Allow exhaust to cool before attempting installation. Severe injury or burns could occur if safety measures are not taken.
Read the rest of this entry »

• 0 Comments

Installation Procedure:
1. Remove truck bed
2. Chalk front tires to ensure truck does not roll.
3. Jack rear of truck up at FRAME RAIL and secure with jack stand at REAREND. Duplicate on both sides. Remove wheels, shocks, sway bar and mounts. When finished rear of truck should be suspended by 2 jack stands on axle with wheels removed and suspension STILL INTACT.
4. Using FRAME SECTION as guide, place FRAME SECTION next to outside of truck frame rail to check for clearances of rivets, tabs, and brackets etc. that will impede the FRAME SECTION from sliding onto frame rail.
5. Remove and/or relocate any rivets, tabs, brackets etc.
6. Slide FRAME SECTION over frame rail into place, it will be a tight fit and usually will need help with a mallet to knock onto frame rail.
7. Repeat steps 4 through 6 on opposite side.
8. With FRAME SECTION in place mount REAR CROSS MEMBER to top rear of notch next to upper bag placement. Loosely bolt REAR CROSSMEMBER in place to allow movement.
Read the rest of this entry »

• 0 Comments

Installation of a Performance Automotive group body lift will change the center of gravity and the handling characteristics of the vehicle. Because of the higher center of gravity and larger tires, the vehicle will handle and react differently both on and off road. You must drive it safely! Extreme care must be taken to prevent vehicle rollover or loss of control, which could result in serious injury or death. Avoid sudden sharp turns or abrupt maneuvers and always make sure all vehicle occupants have their seat belts fastened.
Read the rest of this entry »

• 0 Comments

Pre-fit before painting. Install new, unpainted parts according to these instructions. Then remove parts, paint them and re-install. Painted or Altered Parts are Non-Refundable. The exhaust system must be installed before the side skirts. Do not tighten exhaust clamps or bracket until installation is complete. The entire Sniper side skirt kit must be installed before exhaust tip installation. The surface temperature where the 2-sided tape is applied must be 75o or above. This temperature must be maintained for 24 hours without moving vehicle or the 2-sided tape will fail.
Read the rest of this entry »

• 0 Comments