Removal Of Automatic Locking HubCaution: The brake shoe and brake drum grease is a special type and should not be substituted when it is necessary to change the grease, replace the hub body and brake assembly and/or brake drum 2. Remove axle bolt with washer. 3. Remove hub body. a. Remove the mounting nuts. b. Using a brass bar and hammer, tap on the bolt heads and remove the cone washers. Caution: Do not tap the hub body when removing the cone washer. If the stud bolt is damaged or deformed, replace with a new one. c. Pull off the hub body. 4. Read the rest of this entry »

• 0 Comments

1. Remove the stock shift knob and boot cover.
2. Carefully slide an exacto knife under the clip on the right side of the assembly to remove it. CAUTION : Be extremely careful in this step, if the knife is torqued too hard the blade could break and become a dangerous projectile.
3. Insert a flat head screw driver into the gap created by the exacto knife to pry the clip off.
4. Use a punch to drive out the pin on the opposite side of the shifter. Tap lightly with a hammer until the pin is driven out of the assembly.
5. Remove the four bolts securing the plastic assembly to the chassis.
Read the rest of this entry »

• 1 Comment

The E30 3-Series range first became available in the UK in March 1983, and continued in production until April 1991, when the revised E36 3-Series range (not covered by this manual) was introduced. Convertible and Touring (Estate) models were introduced for 1988, and these models have continued in E30 form to date. The E28 5-Series models were introduced in October 1981, and were superseded in June 1988 by the revised E34 5-Series range, Touring versions of which became available from March 1992. Throughout this manual, E28 models are also referred to as “old-shape”, while E34 models are designated “new-shape”.
Read the rest of this entry »

• 0 Comments

Notes:
• Tool kit contains more parts than are required for Chrysler RWD installation – follow instructions.
• This tool kit can also be used to install 56361-01K case repair sleeve in A4LD, 4R44/55E, 5R55E, AOD & E and 4R70W

Installation Instructions
1. Remove valve body and manual shaft seal.
2. Clean seal bore and pan/valve body surface of case. Run a file across case pan gasket surface to make sure there are no nicks or burrs where the reamer guide plate attaches to case.
Read the rest of this entry »

• 0 Comments

VS131 Setting/Locking Tool Kit includes the Camshaft Setting Tool to ‘lock’ the camshaft in its correct timing position, a Crankshaft Locking Pin and Injection Pump Locking Pin. Additionally the kit includes the essential Timing Adjustment Assembly required to adjust and fix pump timing/cam sprocket position during the engine timing procedure. The correct engine ‘timing’ position will need to be re-established whenever service work requiring cylinder head removal, camshaft/valve train adjustment, or major engine repair has been carried out.
Read the rest of this entry »

• 0 Comments

The VS171 twin cam setting/locking tool kit has been designed for use on multi-valve engines (twin cam) to lock the camshafts, which are under pressure from compressed valve springs, from rotating out of their timing positions when the timing belt is removed. If the camshafts are allowed to move from their timing position possible damage to the inlet and exhaust valves may occur due to contact with the piston crown. By locking the camshafts in position it will allow easier replacement of the drive belt and reduce the risk of incorrect valve timing from taking place. The kit includes camshaft locking pins which can also cover specific crankshaft/flywheel locking applications.
Read the rest of this entry »

• 0 Comments

The Mk. II Volkswagen Golf and Jetta range of models was bucket tappets, the Digifant, Digijet and Mono-Jetronic fuel injection introduced in March 1984, revised body and trim features being the systems, the 16-valve engine fitted to the GTi variant, the fully main visual difference to the earlier range of models. electronic ignition system (FEI), the 085 5-speed gearbox and several The engine/transmission is mounted transversely at the front of the other minor modifications and revisions. As with earlier models the new range is proving popular, giving vehicle, drive being to the front wheels. Detailed improvements have been made throughout the years of manufacture to improve power economy, reliability, comfort and, if previous models can be used as a yardstick, long life. output and economy. These include the introduction of hydraulic. Your Volkswagen Golf and Jetta Manual
Read the rest of this entry »

• 0 Comments

The VS130 Setting and Locking Tool Kit includes all the tools required to maintain the crankshaft gear and camshaft sprockets at TDC for service work requiring timing belt removal, renewal and installation on the Ecotec V6 multi-valve engine. The kit includes the essential timing gauge for
checking camshaft sprocket timing mark alignment during installation of the timing belt.
WARNING! Incorrect installation of the timing belt/engine timing positioning will result in engine damage.
Read the rest of this entry »

• 0 Comments

Instruction manual for toyota yaris from Blitz Performance. This kit was produced for a standard stock car. In the case where this kit is installed on a vehicle other than stock, we are unable to guarantee its functional efficiency and durability of the product. Please be careful when installing this product, whereas no foreign objects or liquids get into it. The result of foreign materials getting mixed into the products may cause malfunctions in the products. During installation, in case of any uncertainties, it is important to have a factory service manual at hand. Read the rest of this entry »

• 0 Comments

Use this definitive 4-wheel drive front axle engagement guide to understand, diagnose, and repair those mysterious 4-wheel drive front axle issues. This guide explains how the OEM units function, what causes them to fail, and which corrections are available. WHAT IS 4X4 POSI-LOK? 4×4 Posi-Lok is the patented cable activated engagement device designed to replace the failure prone vacuum and electric front axle engagement systems. 4×4 Posi-Lok is not a posi-trac or locker. 4×4 Posi-Lok is simple and easy to install and allows you to engage your front axle from inside the cab. Posi-Lok guarantees that your 4-wheel drive will engage every time because you are in direct control of front axle engagement. A one inch pull of the 4×4 Posi-Lok cable ensures you will have 4-wheel drive when you need it, as long as the transfer case is engaged.
Read the rest of this entry »

• 0 Comments