This blower motor has undergone some changes in design so the installation procedures have also changed. The original motor was a two piece motor and the wheel was secured with a set screw. GM changed the design to a one piece unit with a fiberglass heat shield and the wheel is pressed on. On some of the models you may need to remove the front cradle bolts so the engine can be rocked forward. This will help keep the valve cover from interfering with the blower motor replacement. On all models; disconnect the negative battery cable.
Read the rest of this entry »

• 0 Comments

The intent of this bulletin is to provide technicians information regarding the proper installation of the Heating, Ventilation and Air Conditioning (HVAC) Module blower motor (with impeller) assembly.
The current available HVAC Module blower motor for the above listed vehicles can be identified by the three mounting holes (1). The original equipment blower motor had five mounting holes.
In order to avoid confusion and ensure a high level of customer satisfaction, when replacing an HVAC Module blower motor, refer to this bulletin for the appropriate procedure.
Read the rest of this entry »

• 0 Comments

LIGHT DISARM RESISTORS
The resistors are connected into the wiring at each wheel to bypass the original dampening solenoid so that the Road Sensing Suspension will function without giving the driver a suspension error message on the instrument cluster.

INSTALL RESISTORS
Cut the wires leading to the dampening solenoid on the strut/shock. Connect the wires to the ends of the resistor. (This is an in-line resistor so it does not matter which wire goes in or out.) Tape up both ends with suitable electrical tape to prevent both shorts and corrosion. Tie back out of way with a plastic strap.
Read the rest of this entry »

• 0 Comments

Raise and support vehicle, allowing suspension to hang free.
Remove the wheel.
Disconnect the shock absorber electrical connector.
Support the lower control arm with a jack stand or screw jack in order to relieve the spring load.
Remove the lower shock absorber nut(s) and bolt(s).
Remove the upper mounting nut(s). On some models, the upper shock mounting nuts are located in the trunk behind the trim cover.
Remove the shock from the vehicle. On some models, you may have to compress the shock by hand to remove from the mounting.
Read the rest of this entry »

• 0 Comments

For best results, please read all instructions thoroughly prior to attempting installation of your SIR MICHAEL’S Cadillac taillight kit. SIR MICHAEL’S recommends the use of approved hand, eye and ear safety equipment while performing this installation. If you have any questions concerning the installation of your SIR MICHAEL’S Cadillac taillight kit.
NOTE: Any part that is modified and/or painted are non returnable.
Read the rest of this entry »

• 0 Comments

Motor vehicle theft is a serious problem in many parts of the world. In the United States, the annual loss from car theft is over $4 billion. The Automotive Information Council reports that over one million motor vehicles are stolen in the U.S. each year. That’s one motor vehicle theft every 31 seconds.
Read the rest of this entry »

• 0 Comments

1995 ENGINE PERFORMANCE General Motors Corp. Removal, Overhaul & Installation Cadillac; Concours, DeVille, Seville
* PLEASE READ THIS FIRST * CAUTION: When battery is disconnected, vehicle computer and memory systems may lose memory data. Driveability problems may exist until computer systems have completed a relearn cycle. See COMPUTER RELEARN PROCEDURES article in GENERAL INFORMATION section before disconnecting battery.
Read the rest of this entry »

• 0 Comments

The GMRC-03 is designed to be used in Cadillac’s that do not have Onstar or amplified systems. It will retain the warning chimes that are lost when the factory radio is removed. The GMRC-03 will also provide a 12 volt switched accessory wire for proper radio operation. *Note: The GMRC-03 can be used in Cadillac’s that come with a factory amplifier; however the factory amplifier must be bypassed and the speaker wires on the GMRC-03 must not be used. Running new wires to the speakers is recommended. If the Cadillac also has Onstar, that feature will be lost.
Read the rest of this entry »

• 0 Comments

Subject: Starter motor Failure
Model: Ford 2.0 TDCI FWD & 2.4 TDCi RWD/2.0 TDCi FWD
On inspection, the units do not exhibit any manufacturing defects. The premature failure of the unit is due to contamination of the pinion/drive area from metal dust particles produced within the Dual-mass Flywheel, when the clutch wears or becomes overheated. During scheduled servicing, it is recommended that the clutch is checked and if found to be showing signs of wear should be replaced.
Read the rest of this entry »

• 2 Comments

This Fast Response Circuit is designed specifically for use with DODGE D-Series Motor Brakes. It will allow the brake to provide a faster drop out time (time to braking). Part number 031386 is for use with 115/230 VAC brake coils. Part number 031389 is for use with 230/460 VAC brake coils.
Read the rest of this entry »

• 0 Comments