This Quick Reference Guide will give you a quick and clear overview of the operation and function of your vehicle. You’ll also tind descriptions of some additional features. Keep in mind that not all vehicle features are described in this Quick Reference Guide. This Quick Reference Guide is not a substitute for the Owner’s Manual. The Owner’s Manual contains detailed information about all your vehicle’s features plus important warnings and information about passenger safety. Please read it carefully.
Read the rest of this entry »

• 0 Comments

1990-1993 Wiring Chart Circuit LG/W GY/W R/W R/Y P/W LB R/Y GY BK/LB, PK/LG BK/Y T/Y Not Used LB/R BK Circuit Function Left Turn Indicator Hi Beam Indicator Coolant Temperature Sender Feed 12V Input1 Check Brake Indicator Feed Low Coolant Indicator Feed 12V Input1 Check Oil Indicator Feed Malfunction Indicator Lamp (MIL) Feed Air Bag Indicator Tachometer Feed Not Used Illumination Feed Ground Pin Number Circuit Not Used R/LG Not Used Not Used Not Used Not Used R/Y W/R BK Y/W LB/R W/LB DG/LG LG/R Circuit Function Not Used Ignition Switch Not Used Not Used Not Used Not Used 12V Input1 Oil Pressure Gauge Feed Ground Fuel Gauge Feed Illumination Feed Right Turn Indicator Fasten Belts Indicator Battery Indicator Feed
Match to same colors as the 1987-1989 harness.
Read the rest of this entry »

• 0 Comments

This B&M Short Throw Shifter has been designed to work on most 1996-2000 Audi A4, 2000 Audi S4, 2000 Audi A6, and 1996-2000 Volkswagen Passat models. It has been engineered to greatly reduce shift throw and improve shifter feel. Check the parts and tools lists at the beginning of these instructions for the supplied parts and the tools required to install your B&M Short Throw Shifter. Installation of the B&M Short Throw Shifter can be accomplished by anyone with minimal mechanical experience.
Read the rest of this entry »

• 0 Comments

OIL PAN – A4 Removal & Installation
1.To bring lock carrier into service position, see LOCK CARRIER .
2. Raise and support vehicle. Drain engine oil into suitable container.
3. Remove noise insulation panel from under engine.
4. For oil pan removal and installation procedures, refer to Fig. 84 -Fig. 93 .
Read the rest of this entry »

• 0 Comments

Tests/Procedures: 1. Question the customer. Check if he/she started the car, cranked the heater fan on full and went back inside as the car warmed up on a sub-zero morning. Engine temperature rise did not occur at the rate the Powertrain Control Module (PCM) expected. 2. Coolant concentrations of greater than 50/50 can cause this code. Tech Tips: This code will set if the heater system is pulling too much heat from the engine as it is warming up. Engine temperature rise did notoccur at the rate the PCM expected. 2 – Engine Coolant Temperature (ECT) Sensor Confirmed Fix 1 – Coolant Protection 1 – Engine Coolant Level, Engine Coolant Temperature (ECT) Sensor.
Read the rest of this entry »

• 0 Comments

This manual is intended for the installation of the Powerdyne Supercharger kit, Part Number K10513 on the Dodge 318 or 360 C.I. motors, model years 1999–2000 This kit is designed to be 50 state smog legal and as of the writing of this manual C.A.R.B. (California Air Resources Board) exemption is pending. This kit already complies with Federal EPA memorandum 1A, making it smog legal in 49 states, providing your states pollution laws do not supercede EPA memorandum 1A.
Read the rest of this entry »

• 0 Comments

Hot steam can escape from the expansion tank when the filler cap is opened. Cover the filler cap with a cloth and unscrew it carefully. Note: When the engine is hot the cooling system is under pressure. Carefully open filler cap on expansion tank to release pressure before starting repair work. Hoses are secured with spring-type clips. When repairing only use spring-type clips. VAG 1921 pliers are recommended when installing spring-type clips. The O-rings installed at the quick-release connections must be replaced if damaged or leaking. When installing coolant hoses, make sure that they are free of stress and do not come into contact with other components (observe markings on coolant connection and hose). Perform leak test on cooling system with cooling system tester VAG 1274 and adapter VAG 1274/8.
Cooling system components (on body), removing and installing
Read the rest of this entry »

• 0 Comments

This manual includes information for all options available on this model Therefore you may find some information that does not apply to your vehicle All information specifications and illustrations in this manual are those in effect at the time of printing NISSAN reserves the right to change specifications or design without notice and without obligation IMPORTANT INFORMATION ABOUT THIS MANUAL You will see various symbols in this manual They are used in the following ways WARNING This is used to indicate the presence of a hazard that could cause death or serious personal injury To avoid or reduce the risk the procedures must be followed precisely The inside pages of this manual contain a minimum of 50 recycled fibers including 10 post consumer fibers CALIFORNIA PROPOSITION 65 WARNING WARNING Engine Exhaust some of its constituents and certain vehicle components contain or emit chemicals known to State of California to cause cancer and birth defects or other reproductive harm 2000
Read the rest of this entry »

• 0 Comments

1999-2000 SUSPENSION’ ‘Front Removal (Except Odyssey & S2000)
1. Loosen lug nuts with vehicle weight on tires. Pry lock tab away from spindle nut, and loosen nut. Raise and support vehicle. Remove lug nuts and spindle nut. Remove wheel assembly. Remove brake hose mounting bolts, caliper assembly, and support aside. DO NOT put weight on flexible brake line.
2. Remove brake disc retaining screws. Install two 8 x 1.25-mm bolts in brake disc, and tighten bolts to force brake disc from hub. Alternate tightening of bolts to prevent brake disc from binding on hub. Disconnect ABS wheel sensor (if equipped) from steering knuckle and set aside. DO NOT disconnect sensor connector. Remove cotter pin and nut from tie rod end.
Read the rest of this entry »

• 0 Comments

This kit was designed for use with TM Kit# F4531. Use of this kit with other suspension kits and shocks, including coilovers, has not been verified. Proceed with caution. Interferences may exist. This kit should only be installed on a vehicle that is in good working condition. Before you install the kit, thoroughly inspect the vehicle for corrosion or deformation of the sheet metal. If the vehicle is suspected to have been in a collision or misused, do not install this kit. Off-road use of your vehicle with this kit installed may increase the stress applied to the factory components. Failure to observe this warning may result in serious personal injury and/or severe damage to your vehicle.
Read the rest of this entry »

• 0 Comments