The information below documents the procedure I used to install the Hella Micro DE fog lamps on Saab 92-X.
Disclaimer: This information is provided as a reference and the author assumes no responsibility for any damage that may result from this modification to your car.
1. Prep: I started by purchasing the stock Subaru Fog Lamp Relay and Fog Lamp Switch. Since the car is pre-wired for the factory fog lamps, this allows you to use the existing wiring for the installation of the Hella fog lamps.
The part numbers for the parts are: The Fog Lamp Relay is B48 in the diagram below and is the 3rd relay from the bottom. The location will be the only one empty. The Fog Lamp switch is connected to B160, which will be right behind the switch location. By removing the change holder, I was able to install the relay and switch, and plug the connector into the back of the switch without removing the lower dash panel, but it requires some patience.
Read the rest of this entry »

• 0 Comments

1990-1993 Wiring Chart Circuit LG/W GY/W R/W R/Y P/W LB R/Y GY BK/LB, PK/LG BK/Y T/Y Not Used LB/R BK Circuit Function Left Turn Indicator Hi Beam Indicator Coolant Temperature Sender Feed 12V Input1 Check Brake Indicator Feed Low Coolant Indicator Feed 12V Input1 Check Oil Indicator Feed Malfunction Indicator Lamp (MIL) Feed Air Bag Indicator Tachometer Feed Not Used Illumination Feed Ground Pin Number Circuit Not Used R/LG Not Used Not Used Not Used Not Used R/Y W/R BK Y/W LB/R W/LB DG/LG LG/R Circuit Function Not Used Ignition Switch Not Used Not Used Not Used Not Used 12V Input1 Oil Pressure Gauge Feed Ground Fuel Gauge Feed Illumination Feed Right Turn Indicator Fasten Belts Indicator Battery Indicator Feed
Match to same colors as the 1987-1989 harness.
Read the rest of this entry »

• 0 Comments

1. Open driver side door. Lower window.
2. Remove door lock cover.
3. Unsnap and remove the triangular molding that covers the mirror mounting screws.
4. Unsnap and remove the molding that covers the door handle. Remove the screw behind the door handle.
5. Unsnap the control console and unplug the wires. Remove the screw located behind the arm rest.
6. Dislodge the door panel by pulling it up and away from the door slightly. Disconnect light and tweeter connections and remove door panel.
7. Secure mirror with one hand. Proceed cautiously to avoid dropping articles into the door panel. Remove the 3 mirror mounting nuts using a 10mm socket.
Read the rest of this entry »

• 0 Comments

Installation Procedure:
1. Remove the PLASTIC BUMPER FASCIA mounted to the bottom of the front bumper. For the Avalanche, remove the entire plastic bumper. Disconnect the fog lamp electrical harnesses prior to removing the bumper. Note: The airfoil/bumper will need to be permanently removed or notched to accommodate the undercarriage assembly.
2. Remove and discard the three bolts that secure each tow hook to the truck frame. The tow hooks should remain in the same position.
3. Align the undercarriage mount pockets (at each end of the PUSH BEAM WELDMENT) with the tow hook mounting brackets on the vehicle. Note: Use a floor jack to help facilitate the installation procedure.
Read the rest of this entry »

• 0 Comments

- Locate rear bumper attachment point on driver side.
- Remove bumper fasteners.
- Install mounting bracket onto linkage as shown. Torque to 33 ft-lbs / 44 Nm.
NOTE: 2500, 3500 HD trucks do not use spacer ( 5 ). Use fastener ( 2 ) on HD trucks.
- Slide upper mount over factory studs, install fasteners and torque to 70 ft-lbs / 95 Nm.
- Install step pad assembly onto linkage assembly with two socket cap screws.
- Adjust step pad position side to side. Allow for foot access. Torque allen head bolts to 10 ft-lbs / 13.5 Nm.
Read the rest of this entry »

• 0 Comments

These instructions provide information for the installation of the 60510 Fuel Injection Wire Harness Kit. The contents of these instructions are divided into major Sections, as follows:
1.0 Introduction
2.0 About These Instructions
3.0 Tools Needed
4.0 Pre-Installation and Harness Routing Guidelines
5.0 General Installation Instructions
6.0 60510 & 60511 Fuel Injection Harness Kit
7.0 Start Up
8.0 Trouble Shooting Instructions and Trouble Codes
Read the rest of this entry »

• 0 Comments

RGB Module Connections & Controls
The NV_RGB_X Video Interface is capable of both single video and dual video modes of operation. For dual video mode, the optional remote control pad is recommended for switching between the video inputs on the module.
Installation With Plug And Play Factory Harness
Read the rest of this entry »

• 0 Comments

INSTALLATION
NOTE: You will need a #50 Torx bit for this installation
1. Assemble the harness support rods as shown below using the provided heim joints and nuts. Leave at least ¼” of thread showing on each heim joint to allow for adjustment during installation. Do not fully tighten the nuts at this time. NOTE: One end of each of the support rods has reversed thread.
Read the rest of this entry »

• 0 Comments

Supplemental Restraint System SRS (a) Failure to carry out procedures listed below could result in possible deployment of airbag, personal injury, or unnecessary repairs to SRS. (b) Turn the key switch to the LOCK position. (Fig. 1) (c) Remove the key from the ignition switch. (d) Disconnect the negative battery cable. (Fig. 2) (e) Never use a voltmeter to trouble shoot any of Accidentally probing the connectors to the SRS can lead to deployment of the airbag. (Fig 3) (f) SRS wire harness loom/cover is bright yellow in color.
Read the rest of this entry »

• 0 Comments

Preparation
1. Ensure all lamps and accessories are OFF.
2. Ensure the ignition switch is in the OFF position.
3. Loosen the negative battery cable bolt.
Remove negative battery cable from terminal and position away from battery.
4. Wait one (1) minute prior to working on the vehicle to assure SIR roof rail airbag system has been disabled for your safety. Install Camera into Endgate
Read the rest of this entry »

• 0 Comments