2001 suburban rear caliper search result
For rear disc pad removal and installation, DO NOT disconnect brake hose from caliper (wire aside). Replace all pads on an axle if wear indicator on any pad contacts rotor or if pad is worn to within .03″ (.8 mm) of pad backing.
Removal (”A”, “B”, “C”, “K” & “U” Series)
1. Remove 2/3 of brake fluid from master cylinder reservoir. Raise and support vehicle. Remove wheel. Using “C” clamp, compress caliper piston until it bottoms out in its bore.
Read the rest of this entry »
The rear disc brake system consists of a solid rear disc brake rotor (5) and a single-piston rear disc brake caliper. The rear brake pads and linings are held in position between the rear disc brake caliper and the rear disc brake rotor by two guides, two shims, and an M-spring. It is not necessary to remove the rear disc brake caliper completely to replace the rear brake pads and linings; the rear brake pads and linings can be removed simply by pivoting the rear disc brake caliper on its rear disc support bracket.
Read the rest of this entry »
1994-2001 Dodge Ram 4WD 2″ Rear Add-A-Leaf Installation Instructions
17 Mar
Posted by admin as Dodge
PRE-INSTALLATION NOTES.
Refer to OE service manual for proper disassembly/assembly procedures for OE components (like steering shaft, anything else). Consult following instructions for special tools necessary for this installation. Compare parts included in your system with the enclosed parts list. Placing hardware with components before you start may reduce installation time. Contact your Trail Master dealer if any parts are missing or appear to be different than those indicated on the parts list.
Read the rest of this entry »
The instructions step:
• Place the bike on the center stand and remove the current shock absorber.
• Place the Hyperpro shock in the bike, type 461 with reservoir as shown in the picture. If your shock is equipped with the optional hydraulic preload adjuster place the banjo bolt of the HPA to the right side of the bike.
• Use the two added clamps and rubber blocks to mount the reservoir on the sub frame
Read the rest of this entry »
Removal Procedure
1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle General Information.
2. Disconnect the electrical connector and air line if equipped with Real Time Damping (RTD) .
3. Support the rear axle.
4. Disconnect the RTD sensor ( if equipped). Refer to Rear Position Sensor Replacement -
Electronic Suspension – Left (15 Series) or Rear Position Sensor Replacement -
Read the rest of this entry »
Designed to compliment Wilwood’s Subaru Impreza WRX front big brake kit, this new generation Rear Disc Brake Kit provides outstanding holding power with an uncluttered look that is easy to install*
Every Subaru Impreza WRX Pro Series rear brake kit gets the powerful clamping force from a pair of billet four-piston Dynalite calipers. Calipers come in black anodized finish with engraved Wilwood logo. The latest edition of the billet Dynalite features stainless steel anti-rattle plates for quiet running and longer wear in the caliper bridges.
Read the rest of this entry »
Rear brakes – disc brake, servicing Rear brake – Girling disc brake for vehicles with Front and All-Wheel Drive, servicing Axle beam Hex socket head bolt, 10 Nm Wheel speed sensor For vehicles with ABS only Insert with solid lubricant G 000 650 Bracket for brake hose Hex socket head bolt, 65 Nm Hex bolt, self-locking, 35 Nm Replace When loosening and tightening, counter-hold at guide pin Guide pins Protective cap Brake pad securing spring Always replace when pads are replaced
Read the rest of this entry »
2001 Subaru Legacy GT Sedan AWD F4-2.5L SOHC Vehicle Level Steering and Suspension Suspension Wheel Bearing Service and Repair
DISASSEMBLE 1. Remove knuckle. Refer to Steering and Suspension. 2. Using ST1 and ST2, remove hub from rear housing. 3. Remove back plate from rear housing. 4. Using a standard screwdriver, remove outer and inner oil seals. CAUTION: Use new oil seals. 5. Using flat bladed screwdriver, remove snap ring. 6. Using ST1 and ST2, remove bearing by pressing inner race. ST1 927430000 HOUSING STAND ST2 927440000 Read the rest of this entry »
2007 Chevrolet Suburban AMSOIL Dual Remote By-Pass Filter System
21 Feb
Posted by admin as Chevrolet
I used an BMK-13 By-Pass Oil Filter System Kit for a 5.3-liter gasoline Chevrolet V8. I have measured and my installation will also work for 4.8 / 5.3 / 6.0 Chevrolet, GMC, and Cadillac. I fabricated a custom steel bracket that simply bolts up to the alternator bracket. I backed out and used the main support bolt for the alternator. I also used two smaller bolts to Read the rest of this entry »
1955-70 Chevrolet Car Rear Axle Brake Kit Installation Instructions
31 Jan
Posted by admin as Chevrolet
This kit is designed to work with 15” or larger wheels.
Instructions:
1. Disconnect the rear hard lines on the rear axle from the wheel cylinders.
2. Disconnect the rear brake hose from the hard lines on the axle.
Read the rest of this entry »
Categories
Archives
Cars PDF Document is proudly powered by WordPress - BloggingPro theme by: Design Disease