WIRING INFORMATION: 2002 Chevy Trailblazer WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE RED and RED/WHITE Ignition Harness STARTER WIRE YELLOW Ignition Harness IGNITION WIRE PINK Ignition Harness SECOND IGNITION WIRE WHITE Ignition Harness ACCESSORY WIRE ORANGE Ignition Harness SECOND ACCESSORY WIRE BROWN Ignition Harness KEYSENSE WIRE (-) LT.GREEN Ignition Harness POWER DOOR LOCK On these vehicles, door locks are controlled by a data bus system. This requires interfacing the door locks in several locations (each of the front doors, the rear hatch, and the fuse box under POWER DOOR UNLOCK the rear seat) or using a databus interface module Read the rest of this entry »

• 0 Comments

1990-1993 Wiring Chart Circuit LG/W GY/W R/W R/Y P/W LB R/Y GY BK/LB, PK/LG BK/Y T/Y Not Used LB/R BK Circuit Function Left Turn Indicator Hi Beam Indicator Coolant Temperature Sender Feed 12V Input1 Check Brake Indicator Feed Low Coolant Indicator Feed 12V Input1 Check Oil Indicator Feed Malfunction Indicator Lamp (MIL) Feed Air Bag Indicator Tachometer Feed Not Used Illumination Feed Ground Pin Number Circuit Not Used R/LG Not Used Not Used Not Used Not Used R/Y W/R BK Y/W LB/R W/LB DG/LG LG/R Circuit Function Not Used Ignition Switch Not Used Not Used Not Used Not Used 12V Input1 Oil Pressure Gauge Feed Ground Fuel Gauge Feed Illumination Feed Right Turn Indicator Fasten Belts Indicator Battery Indicator Feed
Match to same colors as the 1987-1989 harness.
Read the rest of this entry »

• 0 Comments

1. Temporarily remove the grille and permanently remove the airdam. 2. Disconnect the fog lamp wiring if applicable and then remove the plastic bumper cover from the bumper. 3. Remove the bolts that attach the bumper from the end of the frame rails. 4. Install the hanger plates (Ref 7 & 8). Note: On the drivers side make sure not to pinch the power steering hoses and airbag sensor wire. The top plate on the rear of the hanger plate must install above the hoses. Loosely install the u-bolt (Ref 6) with washers (Ref 11) and nuts (Ref 13) thru the top rear plate and use the bumper bolt temporarily to hold the front of the hanger plate in position. Finger tighten the fasteners until all undercarriage parts are in place. 5. Install the pushbeam (Ref 1) square with the bottom of the hanger plates and secure with bolts (Ref 12), Read the rest of this entry »

• 0 Comments

The installation of the replacement door handles are for persons with advanced auto-body skills and it is recommended to have them professionally installed.
Pre-installation Preparation
Step 1: Verify kit contents.
Step 2: Remove protective wrapping from inserts and place on a non-abrasive surface.
Step 3: Remove the door handles from the box.
Read the rest of this entry »

• 0 Comments

This manual contains dismantling data for the following vehicles: MODEL YEAR MAKE MODEL VARIANT ENGINE TRANSMISSION 2007 Chevrolet Trailblazer 4×4 4.2L L6 4L60E
Provide additional support when a vehicle is on a hoist in the following ways:
• Before removing parts, support the opposite end. This helps prevent the vehicle from slipping off.
• Before removing major components, chain the vehicle frame to the hoist pads at the same end as the removal. This helps avoid a tip-off. Read the rest of this entry »

• 0 Comments

Subject: Radio With Six Disc CD Changer Does Not Recognize Loaded CD And Displays An “INITIALIZING” Message, CD Will Not Play, CD Cannot Be Ejected, Or Disc Icon Does Not Illuminate (Reprogram Radio)
Models:
2005-2006 Chevrolet Avalanche, Suburban, Tahoe
2005-2007 Chevrolet Colorado, Express, Silverado Classic, TrailBlazer
2005-2006 GMC Yukon, Yukon XL
2005-2007 GMC Canyon, Envoy, Savana, Sierra Classic
2005-2006 HUMMER H2 with Six Disc CD Changer Equipped Audio System (RPO UC6)
Read the rest of this entry »

• 0 Comments

Deadbolt – Rear Door
1 Tape the REAR DOOR BRACKET TEMPLATE to the inside of the right rear door as shown in Fig. 1.
2 Carefully mark the hole locations with a center punch and drill holes as indicated on the template.
3 Using a metal cutting jigsaw cut away the area indicated by the dashed lines on the template.
4 Tape the DOOR JAMB TEMPLATE to the door as shown in Fig. 2.
Read the rest of this entry »

• 0 Comments

Removal Procedure
Refer to Approved Equipment for Collision Repair Caution in Cautions and Notices. Before beginning the repair, refer to Metal Panel Bonding for proper adhesive applicator preparations and general information.
Read the rest of this entry »

• 0 Comments

WIRING INFORMATION: 2004 Cadillac SRX WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE 12V wires at the ignition harness are low current 12V sources that should not be used to drive any high current positive circuits. Must go to the battery for 12V. LT.GREEN Ignition Harness POWER DOOR LOCK (-) RED/BLACK At Door Lock Switch Inside Driver Door POWER DOOR UNLOCK (-) ORANGE/BLACK At Door Lock Switch Inside Driver Door PARKING LIGHTS (+) DO NOT USE PARKING LIGHTS (-) BROWN/WHITE In Brown Plug At Module Under Glove Box LEFT FRONT DOOR TRIGGER (-) TAN At Driver Door Module In Driver Door RIGHT FRONT DOOR TRIGGER (-) LT.GREEN At Module Inside Right Read the rest of this entry »

• 1 Comment

WIRING INFORMATION 1989 Nissan 240SX WIRE COLOR LOCATION 12V CONSTANT WIRE WHITE Ignition Harness 12V IGNITION WIRE BLACK/RED Ignition Harness 12V ACCESSORY WIRE BLUE Ignition Harness STARTER WIRE BLACK/YELLOW Ignition Harness SECOND STARTER WIRE BLACK/WHITE Ignition Harness PARKING LIGHTS (+) RED/BLUE Back Of Dash Dimmer Switch Or Harness In Driver’s Kick Panel POWER DOOR LOCK (Interrupt wire using a ORANGE BLACK Harness In Drivers Kick Panel Or Harness relay) Coming Into Vehicle From Driver’s Door POWER DOOR UNLOCK (Negative trigger) Same wire as lock Harness In Drivers Kick Panel Or Harness Coming Into Vehicle From Driver’s Door
Read the rest of this entry »

• 0 Comments