Kit parts are prefaced by the word kit and appear in bold print. 1. Carefully read all warnings and instructions completely before beginning.
2. Verify all parts have been received in this kit by checking the parts list at the end of this document.
3. Only install this kit on the vehicle for which it is specified. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-3175.
4. Park vehicle on a clean, dry, flat, level surface and block tires so vehicle cannot roll in either direction. Adhere to recommendations when replacement fasteners, retainers and keepers are called out in the factory service manual. When re-assembling the vehicle it is recommended Read the rest of this entry »

• 1 Comment

Caution!!! Never work on a hot exhaust system. Serious injury in the form of burns can result If the vehicle has been in use and the exhaust system is hot, allow vehicle to cool for at least 1 hour. Always wear eye protection when working under any vehicle. Note: It is our recommendation that you use a hoist or hydraulic lift to facilitate the installation of your new Borla Performance Cat-Back ™ Exhaust System. Taking all under car safety precautions, lift the vehicle using a hoist or hydraulic lift. Once this has been done, you may begin the removal of your old exhaust system from your vehicle. Note: Before removing the original exhaust system from your vehicle, please compare the parts you have received with the bill of materials provided on the previous page to assure that you have all the parts necessary for the installation of your new Borla Performance Cat-Back ™ Exhaust System.
Read the rest of this entry »

• 0 Comments

1. Disconnect the negative battery cable. Loosen the hose clamp on air cleaner box lid. Twist and remove breather hose from air cleaner box lid. 2. Unhook the two air cleaner lid latches on front of box. 3. Remove the air cleaner box lid by sliding it forward, and then up, and out of the factory intake tube. 4. Remove factory air filter from air cleaner box. 5. Remove, and set aside the oil filler cap. Use caution not to drop anything into engine while cap is off. 6. Carefully lift up on the engine cover (it is held in place by grommets, no bolts) to access the hose clamp Read the rest of this entry »

• 0 Comments

Subwoofer Installation 1. Find the fuse block under the hood and open the fuse box cover.
2. Using a 13mm socket and ratchet loosen and remove the fuse box power supply nut.
3. Connect the ring terminal of the power harness to the fuse box power lug and retighten the nut.
4. Route the wire toward the rubber grommet in the fire wall where the hood release cable passes through securing with wire ties where needed.
Read the rest of this entry »

• 0 Comments

Open the liftgate and remove the upper liftgate trim panel.
Remove the right (passenger’s side) D-pillar trim panel.
Install audio/visual display to the right D-pillar trim panel as shown.
Remove the lower liftgate trim panel.
Remove the right C-pillar trim panel.
Remove the right inner quarter trim panel.
Remove the rear fascia and place it on a protected surface.
Read the rest of this entry »

• 0 Comments

Entertainment Systems – FLO TV
FLO TV`99 service provides a superior mobile TV experience that is available to over 200 million people in 105 major U.S. markets. Many key transportation corridors will be covered by the FLO TV network and coverage will extend to 95 percent of where these Americans live, work, drive. That means that you can receive 24/7 programming to keep your entire crew entertained, regardless of the trip duration. Even if you`ve got to keep your eyes on the road, you can enjoy listening to 60 Minutes from CBS Mobile or the
Read the rest of this entry »

• 0 Comments

Detailed Instructions
1 Check off all items against Snorkel Kit List.
2 Remove guard liner, front rubber and windscreen washer reservoir.
3 Tape Template together accurately on gridline 17. Cut down grid line 28 to mark.
4 Place the Airflow Template supplied on the guard, ensuring the guard crease line are followed exactly. The top guard edge line is a guide only as it will vary slightly between pre and post 1997 cherokee’s.
5 Tape over the sites of all hole points to protect the guard. Locate holes as indicated and mark with centre punch. Drill the 8mm holes. Be careful of any wires or other obstructions under the inner guard.
Read the rest of this entry »

• 0 Comments

Proper installation of this kit requires knowledge of the factory recommended procedures for removal and installation of original equipment components. We recommend that the factory shop manual and any special tools needed to service your vehicle be on hand during the installation. Installation of this kit without proper knowledge of the factory recommended procedures may affect the performance of these components and the safety of the vehicle. We strongly recommend that a certified mechanic familiar with the installation of similar components install this kit
Read the rest of this entry »

• 0 Comments

Installation of a Performance Accessories suspension lift kit will change the center of gravity and the handling characteristics of the vehicle. Because of the higher center of gravity and larger tires, the vehicle will handle and react differently both on and off road. You must drive it safely! Extreme care must be taken to prevent vehicle rollover or loss of control, which could result in serious injury or death. Avoid sudden sharp turns or abrupt maneuvers and always make sure all vehicle occupants have their seat belts fastened.
Read the rest of this entry »

• 0 Comments

GUARDIAN MODULE – Remove drivers seat and step-well trim for access. Guardian module should be mounted inside seat pedestal. It can be secured using self-tapping screws or wire ties. Do not secure the module until all harnesses are installed and proper lift operation has been verified.

LED DISPLAY PANEL – This harness can be identified by the blue tape near the 6-pin connector. Locate a suitable position on the dashboard within clear view of the driver for the mounting of the LED Display Panel. LED display harness will be routed under step-well trim (See Fig 2). Drill a ū” hole in the dashboard where you wish the center of the display to be. Snap the blue taped end of the LED display harness into the Guardian Module in the connector labeled in blue “Display”. Run the other end of the harness under the step-well and dash area then through the ū” hole. Snap the other end of the LED display harness into the LED Display Panel. Ensure panel is level, and secure using the supplied screws.
Read the rest of this entry »

• 0 Comments