2003-2004 (KJ) Jeep® Liberty NOTE: This notification applies only to the above vehicles equipped with Remote Keyless Entry (Sales Code GXM) built from April 1, 2003 through December 12, 2003 (MDH 0401XX through 121200).
The rear flip-up window switch on about 120,000 of the above vehicles may be improperly sealed and could allow water to enter into the switch. This can cause the flip-up window to open unintentionally if it is left unlocked. The rear flip-up window switch must be replaced on all affected vehicles.
Read the rest of this entry »

• 0 Comments

Installation Procedure below:
Front Installation:
1. Secure & properly block the tires of the vehicle on a level concrete or asphalt surface.
2. Raise the front of the vehicle in accordance to the manufactures recommendation & support with jack stands.
3. Remove the front tires / wheels.
4. Remove the upper ball joint nut & separate the upper ball joint from the steering knuckle using a ball joint remover or other suitable tool.
5. Disconnect the lower strut fork at the lower control arm & the lower portion of the strut assembly.(See Photo #1)
6. Remove the air box on the passenger side.
7. Remove the 4 upper strut nuts on the strut tower that holds the strut assembly to the strut tower.
8. Separate the strut fork from the strut assembly & remove the strut from the vehicle.
Read the rest of this entry »

• 0 Comments

The installation of the replacement door handles are for persons with advanced auto-body skills and it is recommended to have them professionally installed.
Pre-installation Preparation
Step 1: Verify kit contents.
Step 2: Remove protective wrapping from inserts and place on a non-abrasive surface.
Step 3: Remove the door handles from the box.
Read the rest of this entry »

• 0 Comments

Vehicle preparation:
1. Remove the negative battery cable before installing the cruise control components for safety precautions.
2. Jeep wrangler applications: remove airbag by using (3) trim tool to release metal clips as shown in figure 2. Caution: ensure that battery has been 90 seconds disconnected for more than prior to removal of airbag; failure to heed this warning may result in airbag discharge and may cause serious injury or death.
Read the rest of this entry »

• 0 Comments

Designed to compliment Wilwood’s Subaru Impreza WRX front big brake kit, this new generation Rear Disc Brake Kit provides outstanding holding power with an uncluttered look that is easy to install*
Every Subaru Impreza WRX Pro Series rear brake kit gets the powerful clamping force from a pair of billet four-piston Dynalite calipers. Calipers come in black anodized finish with engraved Wilwood logo. The latest edition of the billet Dynalite features stainless steel anti-rattle plates for quiet running and longer wear in the caliper bridges.
Read the rest of this entry »

• 0 Comments

The mounting procedure outlined below covers the 1997-2002 Jeep Wrangler. Note that a
Front Gross Axle Rating (FGAWR) of 2500 lbs. is required. A suspension upgrade and additional
ballast may be necessary. You will need to refer to the illustrations and familiarize yourself with each
of the undercarriage components and their relative position to each other. Then proceed as follows:
Begin by removing the four screws that hold the plastic “Jeep” valance in place above the
bumper. Keep these screws as they will need to be reinstalled.
Read the rest of this entry »

• 0 Comments

Installation of a Performance Accessories suspension lift kit will change the center of gravity and the handling characteristics of the vehicle. Because of the higher center of gravity and larger tires, the vehicle will handle and react differently both on and off road. You must drive it safely! Extreme care must be taken to prevent vehicle rollover or loss of control, which could result in serious injury or death. Avoid sudden sharp turns or abrupt maneuvers and always make sure all vehicle occupants have their seat belts fastened.
Read the rest of this entry »

• 0 Comments

Removal All Vehicles
1. Remove the rear door interior trim panel. For additional information, refer to INTERIOR TRIM AND ORNAMENTATION .
2. Remove the access hole watershield.
3. Reconnect the window regulator and window switch electrical connectors and position the front door window to access the glass clamp bolt.
4. Disconnect the window regulator and window switch electrical connectors
5. Loosen the window glass clamp bolt.
Read the rest of this entry »

• 0 Comments

Preparation
1. Ensure all lamps and accessories are OFF.
2. Ensure the ignition switch is in the OFF position.
3. Loosen the negative battery cable bolt.
Remove negative battery cable from terminal and position away from battery.
4. Wait one (1) minute prior to working on the vehicle to assure SIR roof rail airbag system has been disabled for your safety. Install Camera into Endgate
Read the rest of this entry »

• 0 Comments

Preparation
1. Ensure all lamps and accessories are OFF.
2. Ensure the ignition switch is in the OFF position.
3. Loosen the negative battery cable bolt.
Remove negative battery cable from terminal and position away from battery.
4. Wait one (1) minute prior to working on the vehicle to assure SIR roof rail airbag system has been disabled for your safety.
Read the rest of this entry »

• 0 Comments