Neon Front Door Instructions:
1. Using a pick tool pry open the screw cover behind the interior door release lever and remove the screw.
2. Remove the screws in the armrest pocket and at the top of the door near the front.
3. For models with manual windows use a window crank removal tool to disengage the pin securing the window
crank and pull the window crank from the door. The triangle shaped piece that houses the side mirror
adjustment control lever will need to be pulled away from the door. Using a panel removal tool gently pry
the bottom of the plastic away from the door to release the fasteners and let it hang by the mirror control cables.
Read the rest of this entry »

• 0 Comments

2004 BODY & ACCESSORIES Body System – Exterior – Freestar Remove:
1. Remove the front door trim panel. For additional information, Refer to FRONT DOOR TRIM PANEL .
2. Position the watershield aside.
3. Remove the parts in the order indicated in the following illustration and table.
4. To install, reverse the removal procedure.
Read the rest of this entry »

• 0 Comments

Step 1-Unpack QuickLIFT kit and verify contents.
Remove all items from the packing tube. You should have the following before beginning:
* (2) Gas Charged Springs
* (4) 3/16″ multi-grip rivets – used on hood brackets
* (4) Self tapping high strength screws – used on fender brackets
* (4) Fender & Hood Steel brackets
* Printed Instructions
* Gas Spring locking clips (already installed on the gas spring ball ends – Remove before assembly – DO NOT LOSE, these are very small and disappear if dropped.)
Read the rest of this entry »

• 0 Comments

2003 – 2005 model year Matrix vehicles produced BEFORE or AFTER the VIN shown below. Part numbers vary based on Matrix vehicles produced before or after the VIN (refer to the Parts Information table in this TSB). Front Doors Repair Procedure Refer to steps 1 – 6 in the Technical Information System (TIS): 2003, 2004, or 2005 model year Matrix Repair Manual: Engine Hood/Door: Front Door: Overhaul.
Read the rest of this entry »

• 0 Comments

1 – Door Removing and installing Door, removing and installing 2 – Lock cylinder housing Remove Lock cylinder housing, removing 3 – Door handle with base Removing and installing Door handle, removing and installing 4 – Cover cap 5 – Bolt 20 Nm Insert with locking fluid D 185 400 A2 6 – Lock plate 7 – Bolt 20 Nm 8 – Locking button Removing and installing Locking knob for release rod, removing and installing 9 – Locking button 10 – Boots 11 – Door lock Removing and installing Door lock, removing and installing 12 – Bowden cable 13 – Interior release handle 14 – Bolt 20 Nm Read the rest of this entry »

• 0 Comments

Removal All Vehicles
1. Remove the rear door interior trim panel. For additional information, refer to INTERIOR TRIM AND ORNAMENTATION .
2. Remove the access hole watershield.
3. Reconnect the window regulator and window switch electrical connectors and position the front door window to access the glass clamp bolt.
4. Disconnect the window regulator and window switch electrical connectors
5. Loosen the window glass clamp bolt.
Read the rest of this entry »

• 0 Comments

The installation of the replacement door handles are for persons with advanced auto-body skills and it is recommended to have them professionally installed.
Pre-installation Preparation
Step 1: Verify kit contents.
Step 2: Remove protective wrapping from inserts and place on a non-abrasive surface.
Step 3: Remove the door handles from the box.
Read the rest of this entry »

• 0 Comments

WIRING INFORMATION: 2004 Cadillac SRX WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE 12V wires at the ignition harness are low current 12V sources that should not be used to drive any high current positive circuits. Must go to the battery for 12V. LT.GREEN Ignition Harness POWER DOOR LOCK (-) RED/BLACK At Door Lock Switch Inside Driver Door POWER DOOR UNLOCK (-) ORANGE/BLACK At Door Lock Switch Inside Driver Door PARKING LIGHTS (+) DO NOT USE PARKING LIGHTS (-) BROWN/WHITE In Brown Plug At Module Under Glove Box LEFT FRONT DOOR TRIGGER (-) TAN At Driver Door Module In Driver Door RIGHT FRONT DOOR TRIGGER (-) LT.GREEN At Module Inside Right Read the rest of this entry »

• 1 Comment

Deadbolt – Rear Door
1 Tape the REAR DOOR BRACKET TEMPLATE to the inside of the right rear door as shown in Fig. 1.
2 Carefully mark the hole locations with a center punch and drill holes as indicated on the template.
3 Using a metal cutting jigsaw cut away the area indicated by the dashed lines on the template.
4 Tape the DOOR JAMB TEMPLATE to the door as shown in Fig. 2.
Read the rest of this entry »

• 0 Comments

DEADBOLT – REAR AND SIDE DOOR
1 Tape the DOOR MOUNTING TEMPLATE to the door as shown in
2 Carefully mark the hole locations with a center punch and drill as indicated on
3 the template.
4 Tape the DOOR JAMB TEMPLATE to the door as shown in Fig. 2.
5 Mark the hole location with a center punch. Drill a 1/4” pilot hole and then enlarge it with a step drill to 3/4”. This will insure a clean and accurate hole.
Read the rest of this entry »

• 0 Comments