The DMF is bolted to a plate on the crank from the engine side. Access to the engine side of the plate can be found on the lower right side of the firewall. The flywheel must be rotated to remove all 8 bolts. Then remove plate from crank Orientation of release fork for Dodge Ram applications Please note that the clutch fork on this vehicle can be installed in the reverse position. When installed incorrectly, the result will be a “growing noise coming from the belt housing end/or a no release condition. Please refer to Figure Number 4 for the correct fork orientation during the assembly process.
Read the rest of this entry »

• 0 Comments

Installation: 2005 Dodge Charger or Magnum
1. Remove the 2 plastic covers that protect the front area under the hood (Fig. 1). They snap into or out of the vehicle.
2. Remove the 2 bolts that hold the hood latch assembly on and set it aside (do not disconnect the cables). Unplug the horn wire and place the wire out of the way (Figs. 1 & 2).
3. Mount speaker to bracket (Fig. 3).
4. Remove all the plastic rivets from the top of the front of the body of the vehicle, then pull the body toward the front of the vehicle (the body is flexible). Slide the 2 U-Nuts onto the support braces (Fig. 4) and place the bracket (with siren attached) on top of the U-Nuts. The front “ears” of the bracket rest on the two U-Nuts which clip onto the support braces (Fig. 4). The rear of the bracket will mount behind the hood latch assembly using the hood latch’s mounting hardware (Fig. 2).
Read the rest of this entry »

• 0 Comments

Read all instructions before starting any work.
1. Remove the old exhaust system assembly from the vehicle. Lubricate the rubber isolators with WD-40, or a similar product, to aid in removal of the metal rod hangers.
2. Install DynoMax front exhaust x-pipe 54320. Finger tighten the inlet clamps.
3. Install DynoMax Super Turbo Mufflers 17662, right hand and left hand. Finger tighten the 2ı⁄₂” clamps that connect the mufflers to the x-pipe.
Read the rest of this entry »

• 0 Comments

Step 1. Driver & Passenger Bottoms/DB&PB: All of the parts of your seat cover are labeled on the inside. Use the “Seat Cover Piece Identification Chart” to identify the pieces. Place the seat cover on with the long hook (sticky) fasteners to the front. Line up the seams of the seat cover to the seams of the seat, they should closely match. Route the hook fasteners under the front of the seat, avoiding any seat mechanisms, and mate them to the carpet on the back edge as shown.
Read the rest of this entry »

• 0 Comments

Front Door Installation for Magnum, Charger, 300C
1. Using a pick tool pry open the screw covers behind the interior door release lever and below the arm rest and remove the screws.
2. Remove the four screws securing the door panel along the bottom.
3. Using the end of a Phillips screwdriver gently depress the center pin of the three plastic retainers securing the door panel. The center pin of the plastic retainer should depress approximately 1/8” and allow the retainer to be removed from the door panel. The two uppermost retainers do not need to be removed in order to remove the door panel.
Read the rest of this entry »

• 0 Comments

Front Door Installation for Magnum, Charger, 300C
1. Using a pick tool pry open the screw covers behind the interior door release lever and below the
arm rest and remove the screws. Fig. 1
2. Remove the four screws securing the door panel along the bottom. Fig. 1
3. Using the end of a Phillips screwdriver gently depress the center pin of the three plastic retainers
securing the door panel. The center pin of the plastic retainer should depress approximately 1/8”
and allow the retainer to be removed from the door panel. The two uppermost retainers do not
need to be removed in order to remove the door panel. Fig. 2
Read the rest of this entry »

• 0 Comments

Do not install the kits listed below on 2003 model year Dodge trucks built up to June 27th 2005 with automatic transmissions without a transmission controller. Pacbrake has kits for these vehicles that include an automatic transmission controller.

C44031 Pacbrake kit is a PRXB design for 2003 model year and newer Dodge trucks built up to January 4th 2004 with a Cummins 5.9L and manual shift transmission only.
Read the rest of this entry »

• 0 Comments

Select the Navigation key on the SETTINGS screen 3 Select the Tracking On Off key 4 Select the On key 11 16 How do I adjust the display REVIEW COPY 2005 nav Navigation System OM USA English nna 07 10 04 debbie GPS INFORMATION DISPLAY The following GPS information will be displayed on the screen latitude longitude altitude signal reception and satellite locations 1.
Read the rest of this entry »

• 0 Comments

Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing a Borla Performance Exhaust System on your vehicle will eliminate the restrictive design of the stock exhaust, allowing your engine to discharge exhaust gas easier. The result is more horsepower and torque, longer engine life, and a distinctive throaty growl- all this, with easy bolt-on installation. These installation instructions have been written to help you in the installation of your Borla Performance Exhaust System. Please read it completely before installing your system.
Read the rest of this entry »

• 0 Comments

1. For the Dakota: Remove bumper, retaining all OEM fasteners for reinstallation.
Proceed to Step 2.
For the Durango: Prior to removing the bumper, cut and remove the center portion of the bumper and air dam as shown in the photo below. Retain the cut out section of the air dam to fabricate an air deflector in Step 8. Remove the remaining bumper assembly, retaining all OEM fasteners for reinstallation.
2. Clamp the driver-side mount plate to the outside of the driver-side vehicle frame. Make sure the mount alignment tab fits up against the back of the vehicle frame front plate, and the front and rear plate stiffeners are snug against the bottom of the frame. When positioned correctly, mount plate holes align near the center of the vehicle frame.
Read the rest of this entry »

• 0 Comments