WIRING INFORMATION: 2002 Chevy Trailblazer WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE RED and RED/WHITE Ignition Harness STARTER WIRE YELLOW Ignition Harness IGNITION WIRE PINK Ignition Harness SECOND IGNITION WIRE WHITE Ignition Harness ACCESSORY WIRE ORANGE Ignition Harness SECOND ACCESSORY WIRE BROWN Ignition Harness KEYSENSE WIRE (-) LT.GREEN Ignition Harness POWER DOOR LOCK On these vehicles, door locks are controlled by a data bus system. This requires interfacing the door locks in several locations (each of the front doors, the rear hatch, and the fuse box under POWER DOOR UNLOCK the rear seat) or using a databus interface module Read the rest of this entry »

• 0 Comments

Subject: Radio With Six Disc CD Changer Does Not Recognize Loaded CD And Displays An “INITIALIZING” Message, CD Will Not Play, CD Cannot Be Ejected, Or Disc Icon Does Not Illuminate (Reprogram Radio)
Models:
2005-2006 Chevrolet Avalanche, Suburban, Tahoe
2005-2007 Chevrolet Colorado, Express, Silverado Classic, TrailBlazer
2005-2006 GMC Yukon, Yukon XL
2005-2007 GMC Canyon, Envoy, Savana, Sierra Classic
2005-2006 HUMMER H2 with Six Disc CD Changer Equipped Audio System (RPO UC6)
Read the rest of this entry »

• 0 Comments

RGB Module Connections & Controls
The NV_RGB_X Video Interface is capable of both single video and dual video modes of operation. For dual video mode, the optional remote control pad is recommended for switching between the video inputs on the module.
Installation With Plug And Play Factory Harness
Read the rest of this entry »

• 0 Comments

1990-1993 Wiring Chart Circuit LG/W GY/W R/W R/Y P/W LB R/Y GY BK/LB, PK/LG BK/Y T/Y Not Used LB/R BK Circuit Function Left Turn Indicator Hi Beam Indicator Coolant Temperature Sender Feed 12V Input1 Check Brake Indicator Feed Low Coolant Indicator Feed 12V Input1 Check Oil Indicator Feed Malfunction Indicator Lamp (MIL) Feed Air Bag Indicator Tachometer Feed Not Used Illumination Feed Ground Pin Number Circuit Not Used R/LG Not Used Not Used Not Used Not Used R/Y W/R BK Y/W LB/R W/LB DG/LG LG/R Circuit Function Not Used Ignition Switch Not Used Not Used Not Used Not Used 12V Input1 Oil Pressure Gauge Feed Ground Fuel Gauge Feed Illumination Feed Right Turn Indicator Fasten Belts Indicator Battery Indicator Feed
Match to same colors as the 1987-1989 harness.
Read the rest of this entry »

• 0 Comments

These instructions provide information for the installation of the 60510 Fuel Injection Wire Harness Kit. The contents of these instructions are divided into major Sections, as follows:
1.0 Introduction
2.0 About These Instructions
3.0 Tools Needed
4.0 Pre-Installation and Harness Routing Guidelines
5.0 General Installation Instructions
6.0 60510 & 60511 Fuel Injection Harness Kit
7.0 Start Up
8.0 Trouble Shooting Instructions and Trouble Codes
Read the rest of this entry »

• 0 Comments

WIRING INFORMATION: 2003 Lincoln Aviator WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE YELLOW Ignition Harness STARTER WIRE DK.GREEN Ignition Harness IGNITION WIRE RED/LT. GREEN Ignition Harness ACCESSORY WIRE GRAY/YELLOW Ignition Harness POWER DOOR LOCK (-) PINK/YELLOW Harness In Driver’s Kick Panel POWER DOOR UNLOCK (-) PINK/LT. GREEN Harness In Driver’s Kick Panel • The factory module that controls the door locks shuts down to conserve power. When installing an aftermarket keyless entry system, hook up dome light supervision and program the aftermarket system for a double-pulse unlock to “wake up” the module and unlock the doors. PARKING LIGHTS (+) BROWN Headlight Switch DOOR TRIGGER (+) BLACK/LT. BLUE Harness In Driver’s Kick Panel or Courtesy Light Under Dash DOME LIGHT SUPERVISION USE DOOR TRIGGER REAR HATCH TRIGGER COMMON WITH DOORS REAR HATCH RELEASE (+) PURPLE/YELLOW OEM Read the rest of this entry »

• 0 Comments

WIRING INFORMATION: 2004 Cadillac SRX WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE 12V wires at the ignition harness are low current 12V sources that should not be used to drive any high current positive circuits. Must go to the battery for 12V. LT.GREEN Ignition Harness POWER DOOR LOCK (-) RED/BLACK At Door Lock Switch Inside Driver Door POWER DOOR UNLOCK (-) ORANGE/BLACK At Door Lock Switch Inside Driver Door PARKING LIGHTS (+) DO NOT USE PARKING LIGHTS (-) BROWN/WHITE In Brown Plug At Module Under Glove Box LEFT FRONT DOOR TRIGGER (-) TAN At Driver Door Module In Driver Door RIGHT FRONT DOOR TRIGGER (-) LT.GREEN At Module Inside Right Read the rest of this entry »

• 1 Comment

First, please accept our most sincere “thank you” for choosing this part. In your hands rests the results of a lot of hard work and commitment to standing out in a crowded aftermarket. Your choice in our products allows us to continue to work towards developing more unique and innovative solutions for your performance needs.
Read the rest of this entry »

• 0 Comments

1. Temporarily remove the grille and permanently remove the airdam. 2. Disconnect the fog lamp wiring if applicable and then remove the plastic bumper cover from the bumper. 3. Remove the bolts that attach the bumper from the end of the frame rails. 4. Install the hanger plates (Ref 7 & 8). Note: On the drivers side make sure not to pinch the power steering hoses and airbag sensor wire. The top plate on the rear of the hanger plate must install above the hoses. Loosely install the u-bolt (Ref 6) with washers (Ref 11) and nuts (Ref 13) thru the top rear plate and use the bumper bolt temporarily to hold the front of the hanger plate in position. Finger tighten the fasteners until all undercarriage parts are in place. 5. Install the pushbeam (Ref 1) square with the bottom of the hanger plates and secure with bolts (Ref 12), Read the rest of this entry »

• 0 Comments

STEP 1: The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in the shape as shown in the photos above. For more information on how to remove the radio, see the diagram below.
STEP 2: Pull the radio from the dash. Unplug the antenna cable from the rear of the radio. Unplug the 2 wire harness connectors from the rear of the radio.
Read the rest of this entry »

• 0 Comments