2003-2004 (KJ) Jeep® Liberty NOTE: This notification applies only to the above vehicles equipped with Remote Keyless Entry (Sales Code GXM) built from April 1, 2003 through December 12, 2003 (MDH 0401XX through 121200).
The rear flip-up window switch on about 120,000 of the above vehicles may be improperly sealed and could allow water to enter into the switch. This can cause the flip-up window to open unintentionally if it is left unlocked. The rear flip-up window switch must be replaced on all affected vehicles.
Read the rest of this entry »

• 0 Comments

WIRING OVERVIEW
Switch Settings (read below for explanation)
Selecting The Vehicle Type
Switches 1,2, and 3 are used to select vehicle type. Use the chart on the back of these instructions to determine which of the above switch settings you will need.
Read the rest of this entry »

• 0 Comments

Installation Procedure below:
Front Installation:
1. Secure & properly block the tires of the vehicle on a level concrete or asphalt surface.
2. Raise the front of the vehicle in accordance to the manufactures recommendation & support with jack stands.
3. Remove the front tires / wheels.
4. Remove the upper ball joint nut & separate the upper ball joint from the steering knuckle using a ball joint remover or other suitable tool.
5. Disconnect the lower strut fork at the lower control arm & the lower portion of the strut assembly.(See Photo #1)
6. Remove the air box on the passenger side.
7. Remove the 4 upper strut nuts on the strut tower that holds the strut assembly to the strut tower.
8. Separate the strut fork from the strut assembly & remove the strut from the vehicle.
Read the rest of this entry »

• 0 Comments

DISASSEMBLY
1. Raise vehicle and support with proper jackstands for the weight, leaving the suspension hanging.
2. Use caution around hot exhaust systems to avoid burns.
3. Use penetrating oil on all nuts and bolts.
Read the rest of this entry »

• 0 Comments

Vehicle preparation:
1. Remove the negative battery cable before installing the cruise control components for safety precautions.
2. Jeep wrangler applications: remove airbag by using (3) trim tool to release metal clips as shown in figure 2. Caution: ensure that battery has been 90 seconds disconnected for more than prior to removal of airbag; failure to heed this warning may result in airbag discharge and may cause serious injury or death.
Read the rest of this entry »

• 0 Comments

The mounting procedure outlined below covers the 1997-2002 Jeep Wrangler. Note that a
Front Gross Axle Rating (FGAWR) of 2500 lbs. is required. A suspension upgrade and additional
ballast may be necessary. You will need to refer to the illustrations and familiarize yourself with each
of the undercarriage components and their relative position to each other. Then proceed as follows:
Begin by removing the four screws that hold the plastic “Jeep” valance in place above the
bumper. Keep these screws as they will need to be reinstalled.
Read the rest of this entry »

• 0 Comments

When any of the memory switches are pushed while the automatic drive positioner is operating When the adjusting switch for the driver s seat is turned on while the automatic drive positioner is operating When the memory switch 1 or 2 is not pushed and held for at least 1 second When the seat has been already moved to the memorized position When no seat position is stored in the memory switch When the automatic transmission selector lever is moved from P Park to any other position When the driver s door remains open more than 45 seconds and the ignition switch is not in the ON position The automatic drive positioner system can be adjusted and canceled For vehicles with navigation system see Vehicle electronic systems in the Display screen heater air conditioner and audio systems section of this manual For vehicles without navigation system see your NISSAN dealer Pre driving checks and adjustments
Read the rest of this entry »

• 0 Comments

Tests/Procedures: 1. Ground the Violet/Yellow wire (disarm circuit) that goes to either front door and the theft alarm module. Have the keys out of the ignition and all doors closed when grounding the wire. This should disarm the theft alarm system and prevent the theft alarm from arming. 2. Check that the interior lights do not stay on due to the wire being grounded. If they do, the illuminated entry relay will need to be removed or another method of disabling the theft alarm will have to be used. 3. Another method if the theft alarm module is faulty would be to disconnect the module and replace the Powertrain Control Module (PCM) with a new one.
Read the rest of this entry »

• 0 Comments

This bulletin is being revised to add the 2005 model year and update the part number information for Permatex Quick Grid. Please discard Corporate Bulletin Number 03-08-44-005B (Section 08 — Body and Accessories).
Condition
Some customers may comment that the radio has poor reception or radio static/increased interference when the rear window defogger is turned on. Also, some rear window defogger grids may be inoperative.
Read the rest of this entry »

• 0 Comments

Follow carefully the instructions listed on these pages and use the template provided, do not over tighten bolts. Do not use silicone on any connections, use urethane Ensure that safe work practices are followed when installing your Airflow Snorkel. Protective ear and eye wear should be worn at all times when using power tools.
Read the rest of this entry »

• 0 Comments