1. For the Dakota: Remove bumper, retaining all OEM fasteners for reinstallation.
Proceed to Step 2.
For the Durango: Prior to removing the bumper, cut and remove the center portion of the bumper and air dam as shown in the photo below. Retain the cut out section of the air dam to fabricate an air deflector in Step 8. Remove the remaining bumper assembly, retaining all OEM fasteners for reinstallation.
2. Clamp the driver-side mount plate to the outside of the driver-side vehicle frame. Make sure the mount alignment tab fits up against the back of the vehicle frame front plate, and the front and rear plate stiffeners are snug against the bottom of the frame. When positioned correctly, mount plate holes align near the center of the vehicle frame.
Read the rest of this entry »

• 0 Comments

For easier assembly and installation, vehicle and all snowplow components should be on a smooth, level, hard surface, such as concrete.
1. Remove bumper from bumper brackets. Retain fasteners.
2. Remove bumper brackets from frame. Diesel and V10 applications: On these applications you must first remove the top two intercooler fasteners. Then push intercooler up and out to provide clearance to remove bumper bracket bolt assembly.
Retain fasteners.
Read the rest of this entry »

• 0 Comments

Read instructions before assembling. Fasteners should be finger tight until instructed to tighten according to the torque chart. Use standard methods and practices when attaching snowplow including proper personal protective safety equipment.

INSTALLATION INSTRUCTIONS
NOTE: For easier assembly and installation, vehicle and all snowplow components should be on a smooth, level, hard surface, such as concrete.
1. Remove license plate bracket and retain for vehicle owner. Remove bumper from bumper brackets. Retain fasteners.
Read the rest of this entry »

• 0 Comments

This manual is divided into different areas to assist you with your installation and operation of your braking unit. We strongly suggest that you write down the kit and serial numbers of your unit in the spaces provided and retain this manual for any future reference
Kit Contents
2033135 – 1988-1998 Dodge Cummins 12V Exhaust Brake Kit
1 1230030 Vacuum Control Kit (w/ Micro Switch)
1 1230335 Vacuum Spool Valve Kit
1 2133030 Exhaust Brake
Read the rest of this entry »

• 0 Comments

Do not install the kits listed below on 2003 model year Dodge trucks built up to June 27th 2005 with automatic transmissions without a transmission controller. Pacbrake has kits for these vehicles that include an automatic transmission controller.

C44031 Pacbrake kit is a PRXB design for 2003 model year and newer Dodge trucks built up to January 4th 2004 with a Cummins 5.9L and manual shift transmission only.
Read the rest of this entry »

• 0 Comments

READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS BRACKETRON PHONE MOUNT. All instructions are written from the drivers seat position looking forward at the vehicle dash. We advise caution whenever you are removing or handling plastic parts of a vehicles dash. WARNING: Unnecessary force or pressure can cause pieces to crack or break
Read the rest of this entry »

• 0 Comments

This undercarriage fits all models listed but the crossmember connection will vary. Refer to step “a” for the 1987-1996 Dodge Dakota, 1997-2003 Dodge Dakota Sport, 1997-2003 Dodge Dakota SLT Extended Cab and 1998-2003 Dodge Durango SLT models. Refer to step “b” for the 1997-2004 Dodge Dakota and 1998-2003 Dodge Durango
1. Disconnect the fog lamp harnesses if applicable, and then remove the bumper.
a. Remove the bumper mount plates from in between the frame rail and radiator. Discard the mount plate hardware.
b. Permanently remove the air dam from the truck frame crossmember. Remove the fasteners that are pressed into the bumper bracket on the frame rail. Secure the bracket and frame wall with vise grips and then use a hammer to punch out the fasteners.
Read the rest of this entry »

• 0 Comments

All hardware should be tightened only enough to ensure safety during assembly. Fully tighten all hardware after entire assembly is completed.
1. Insert pairs of 5/8 inch x 7 1/2 inch and 5/8 inch x 8 inch hex bolts through holes in four 1/2 inch thick top bars from the kit. Place the 7 1/2 inch bolt/bar assemblies over the side rails of the vehicle ahead of the cab mount structure. Place the 8 inch bolt/bar assemblies over the side rails behind the cab mount structure.
Read the rest of this entry »

• 0 Comments

This mount will provide a great reduction in transmission movement making shifting much more secure. With less transmission movement you’ll have less drivetrain slop as well, resulting in more power transmitted to the wheels. Upgraded engine mounts are recommended to be used in conjunction. Below are our installation guidelines for this item. Please review them carefully before attempting to install this product.
Read the rest of this entry »

• 0 Comments

Installation instructions for the Eclipse, Stratus Coupe, and Sebring Coupe. (See reverse side for Mitsubishi Outlander, Lancer/Sportback, and Mitsubishi Montero instructions)
Locate and remove two (2) screws from the bottom of the trim bezel. With your hands or Dash Trim Tool (#SIT-104), release the bezel from all clips. There are two (2) clips on the bottom and two (2) on the top of this bezel. Remove bezel and set aside carefully.
Read the rest of this entry »

• 0 Comments