Mercury in Maine’s environment is a problem, particularly for infants and young children.
Exposure to mercury can permanently harm the developing brain and nervous system.
The Environmental Protection Agency estimates that 630,000 infants are born every
year in the United States with unsafe levels of mercury in their blood.
Read the rest of this entry »

• 0 Comments

The following procedures for removing the fan clutch gives the factory recommended loosening and tightening directions for the fan hub nut. However, it has been our experience that certain aftermarket parts manufacturers have changed this to enable use of universal fit parts. We recommend trying the factory direction first, then, if the nut doesn’t seem to be moving, reverse the direction. Placing too much load on the water pump snout will break it.
Read the rest of this entry »

• 0 Comments

The steps of timing belt installation for this 1993 Mercury Villager LS.
Removal
1. Disconnect negative battery cable. Raise and support vehicle. Remove covers from below engine. Drain cooling system. Remove right front wheel and engine side cover. Remove accessory drive belts. Remove crankshaft pulley bolt and pulley. 2. Remove upper radiator hose and water inlet hose. Remove A/C compressor idler pulley and bracket. Remove water pump pulley. Remove upper and lower timing belt front covers. See Fig. 1 . 3. Temporarily install crankshaft pulley bolt so crankshaft can be rotated. Set cylinder No. 1 at TDC of compression stroke by rotating crankshaft until marks on camshaft sprockets align with marks on timing belt upper rear cover, and mark on crankshaft sprocket aligns with mark on front cover housing. See Fig. 2 . 4. Loosen timing belt tensioner nut. Release tension on belt. Remove timing belt. Check timing belt tensioner, spring and timing belt.
Read the rest of this entry »

• 0 Comments

REMOVAL & INSTALLATION
WARNING: Deactivate air bag system before performing any service operation. See appropriate AIR BAG RESTRAINT SYSTEMS article in ACCESSORIES & EQUIPMENT. Do not apply electrical power to any component on steering column without first deactivating air bag system. Air bag may deploy.
Read the rest of this entry »

• 0 Comments

Removal Timing Belt(Esteem)
1. Disconnect negative battery cable. Remove right side engine under cover. Remove power steering and A/C compressor drive belts. 2. Remove A/C compressor and power steering pump with hoses attached, and secure out of way. Support engine from above or with floor jack under oil pan. Remove air cleaner case with air cleaner outlet hose. 3. From timing belt end of engine, remove engine mount and mounting bracket. Loosen water pump pulley bolts. Remove water pump drive belt and pulley. 4. Remove 5 crankshaft pulley-to-crankshaft bolts. Remove pulley. It is NOT necessary to remove crankshaft center bolt. Remove timing belt cover. See Fig. 1 . 5. Rotate crankshaft clockwise to align timing marks. See Fig. 2 and Fig. 3 . Stamped “E” on camshaft sprocket must point straight up. Loosen timing belt tensioner bolt and stud nut. Move tensioner away from belt, and hand tighten bolt and nut. See Fig. 4 . 6. If reusing old belt, mark belt with an arrow indicating direction of rotation for installation reference. Remove timing belt.
Read the rest of this entry »

• 0 Comments

The Aviator, which debuted last year, is (like the Mercury Mountaineer) based on the Explorer, Ford’s bestselling, mid-size 16-foot SUV. Although the Lincoln derivative is fundamentally the same as the others, there are a number of significant differences. Lincoln ditched the Explorer’s steering rack in favor of variable-assist and variable-ratio steering gear. The shocks and springs are also exclusive to the Aviator, and its interior is very much Lincoln, being swathed in fine leather, satin nickel, and burled walnut. The second row comes as either a three-passenger bench or with two outboard seats and a center console. There’s just one engine available, a 4.6-liter, DOHC 32-valve V-8 that produces 302 hp and 300 lb-ft of torque. And the standard five-speed automatic transmission is the best Ford slushbox we’ve ever sampled. For 2004, a tire-pressure monitor is standard, and roll-stability control is optional.
Read the rest of this entry »

• 0 Comments

Removal (Frontier, Pathfinder, QX4 & Xterra)
1. Disconnect negative battery cable. Remove the engine undercover. Drain coolant and remove the radiator.
Remove engine cooling fan and water pump pulley. Remove accessory drive belts. Remove spark plugs.
2. Remove distributor protector. Remove A/C compressor drive belt idler bracket. Remove fresh air intake
tube from rocker cover. Remove thermostat housing hose.
3. Rotate crankshaft to set No. 1 cylinder at TDC on compression stroke. See Fig. 1 . Remove crankshaft
pulley bolt and remove crankshaft pulley. Remove front upper and lower timing belt covers. See Fig. 2 .
4. Align punch mark on left camshaft sprocket with punch mark on timing belt upper rear cover. Align
punch mark on crankshaft sprocket with notch on oil pump housing. See Fig. 3 . Install crankshaft pulley
bolt so that crankshaft can be rotated.
Read the rest of this entry »

• 0 Comments

Chevrolet LCT1000–LCT2500, Ford 47RH / 47RE / 48RE, Dodge E4OD / 4R100 Transmission removal, Installation And testing
Removal
Check and record all codes and actions of your transmission before transmission is removed. This will help if you still have problems after installation. Damage to your transmission may have been caused from some other external source.
Read the rest of this entry »

• 0 Comments

For rear disc pad removal and installation, DO NOT disconnect brake hose from caliper (wire aside). Replace all pads on an axle if wear indicator on any pad contacts rotor or if pad is worn to within .03″ (.8 mm) of pad backing.
Removal (”A”, “B”, “C”, “K” & “U” Series)
1. Remove 2/3 of brake fluid from master cylinder reservoir. Raise and support vehicle. Remove wheel. Using “C” clamp, compress caliper piston until it bottoms out in its bore.
Read the rest of this entry »

• 0 Comments

REMOVAL 1. Disconnect the ground cable from battery. 2. Remove the front grille RH and front grille LH. 3. Remove the clips inside the mounting portion of front grille RH and front grille LH. 4. Remove the six clips on the upper part of bumper. 5. Remove the clips, which secure the front bumper to fender. 6. Remove the clips, and turn over the mud guard LH and RH. 7. Remove the three clips in the center, right and left part of Read the rest of this entry »

• 0 Comments