A thermistor built into the engine coolant temperature sensor changes the resistance value according to the engine coolant temperature. The structure of the sensor and connection to the ECM is the same as in the intake air temp. circuit malfunction shown on page DI-26 . If the ECM detects the DTC P0115, it operates the fail-safe function in which the engine coolant temp. is assumed to be 80°C (176°F).
HINT: After confirming DTC P0115 use the OBD II scan tool or TOYOTA hand-held tester to confirm the engine coolant temperature from ”CURRENT DATA”.
Read the rest of this entry »

• 0 Comments

Engine, removing and installing Note: All cable ties opened or cut during engine removal must be reinstalled at the same locations. Remove engine without transmission toward the front. Drained coolant must be stored in a clean container for disposal or reuse. Always replace seals and gaskets. Do not open coolant circulation system.
Read the rest of this entry »

• 0 Comments

This installation requires special expertise from a Webasto training course to install a Webasto Thermo Top C/Z, which means that it may only be installed by a specially trained workshop or dealership. Webasto cannot accept any liability for faults and damage caused by the system being installed by untrained personnel.
Read the rest of this entry »

• 0 Comments

The following procedures for removing the fan clutch gives the factory recommended loosening and tightening directions for the fan hub nut. However, it has been our experience that certain aftermarket parts manufacturers have changed this to enable use of universal fit parts. We recommend trying the factory direction first, then, if the nut doesn’t seem to be moving, reverse the direction. Placing too much load on the water pump snout will break it.
Read the rest of this entry »

• 0 Comments

This write-up describes the process of replacement of a soft top for a Mazda Miata. My vehicle is a 92, but I think that this might be very similar for many model years of Miata. I refer to this as “removal and installation” because removing the old top can be (at least was for me) a task requiring as much effort as installation of the new top. This is particularly true when you are not an expert at removing convertible tops, or have no previous experience replacing Miata tops. Without adequate instructions this can (and did for me) turn into a job taking 15 to 20 hours and requiring a few trips to the hardware store. Instructions from Mazda or from the people who sell you the top might claim that the job will “take you an afternoon with a few common tools”. Good luck with that! I’m writing this in hopes that someone else will not have as much difficulty as I did.
Read the rest of this entry »

• 0 Comments

I replaced the Timing Belt, Water Pump, Tensioning Roller, Tensioning Dampener, and Ribbed (accessory) Belt on my 2002 Audi TT 225 (AMU engine). I documented the process in this write-up, which is intended to serve as a reference only. No liability is assumed for use of any information contained within.
Read the rest of this entry »

• 0 Comments

The VS130 Setting and Locking Tool Kit includes all the tools required to maintain the crankshaft gear and camshaft sprockets at TDC for service work requiring timing belt removal, renewal and installation on the Ecotec V6 multi-valve engine. The kit includes the essential timing gauge for
checking camshaft sprocket timing mark alignment during installation of the timing belt.
WARNING! Incorrect installation of the timing belt/engine timing positioning will result in engine damage.
Read the rest of this entry »

• 0 Comments

The new Audi A6 – the most progressive vehicle takes the lead Design and performance are the main driving elements on its way to the top position. Furthermore, the new Audi A6 embodies the consequent continuation of the familiar Audi brand values, sports appeal, progressiveness and intrinsic quality, which are evident in the fourth generation of this sporty business limousine.
Read the rest of this entry »

• 0 Comments

Powerchip technology enhances your Audi to its ultimate level, delivering faster, smoother acceleration in all driving conditions. Whether you enjoy a leisurely weekend cruise or a hard racetrack drive – there is no easier and more effective way to release the potential from your S4 4.2 V8.

The following information is an overview of the performance the Powerchip will deliver. If you have any questions, your Power Consultant will assist you as best as possible. We look forward to giving you the best performance possible from your Audi.
Read the rest of this entry »

• 0 Comments

This set of two tools allows swift removal of the lock plug from many newer Ford and GM glove compartments. The FPR-2 spreads the plastic retaining arms with minimal risk of breakage, pushing out the plug safely. This operation is necessary when obtaining correct code information. Ford, GM, and many European models including Audi, Saab, and VW utilize this mounting method.
Read the rest of this entry »

• 0 Comments